JGP630BEK1BB General Electric Cooktop - Instructions

A rubber grate foot on my range top had worn out. I pulled the worn foot out and installed the new grate foot with no tools or accessories. Good as new! Now I don't have to worry about the grate scraping my range top and scratching the paint. I also ordered extras so I won't have to wait if another wears out.

openend stove top disconnected wire pushed out old sparker inserted new one closed lid game over

It's not need of repair, just replacement. Take the old part out and put the new part on same place, aligning the pin hole with the pivot on the stove.

determined that the top of the burner was melted and malformed. Repair was simple: lifted off the damaged burner and slipped the new one in place.

Very simple repair with no tools required. Turn off power to stove. Remove grates, remove burner, pull old Top Burner Spark Electrode up being careful not to jerk it up hard - wiggle if necessary, unplug wire from old electrode, plug wire into new electrode making sure it fits snug - if not, squeeze it closed a little at a time until it fits snug, push new igniter into place being careful not to force it and crack the ceramic body. Install burner being careful not to damage the electrode, Install grates. Turn power back on and test to make sure it works. It took me all of 15 minutes to change 2 burner spark electrodes. The only bad thing about this repair is that the shipping costs as much as the parts.

Took longer to open the box.

Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.

I was pretty upset as the grate wobbled, so I went on line and looked for GE Profile parts. To my amazement, I found the little rubber feet quite easily, and within 2 days they were here at my home. I simply had to stick them in the holes; however, I noted that they did not fit real tight, so I removed them and shot a little glue on them, and they have been in place ever since. Thanks to you guys, I am a happy camper now!!!

Order parts and installed - no tools needed - completed repairs less than 1 minute

Unplug the range from its wall socket to avoid electric shock. The various range parts that support a pot or frypan are easily lifted off their perches, exposing the small white igniter. The only moderately difficult aspect is wiggling the igniter out of its retainer. The electric wire leading into it then can be pulled out and fed into the new igniter with a push. Replace igniter in its retainer, then replace the range parts you removed to expose the igniter and plug the range back into the wall socket. Piece of cake.

It's a very simple repair all you do is unplug the stove top remove the burners tops lifting them straight off you'll find two screws on each of them unscrew the two screws lift them off and set them aside you should find gaskets under each one of them ours was not in very good shape at all most were missing lift the top off of the stove top you'll find the wires with a white I believe one was rectangle and the rest were square pieces just pull them straight up you have to give them a little bit of strength to get them off on our stovetop that were five on one wire 1 to the next of a night so on at the end there are two plugs unplug them pull the one straight up you might need a needle-nose plier and the other one is connected to another wire you just pull them apart hands on each one have the new set ready in the center of each of the square white pieces you may have to turn the little piece in the center to line it up with the flat part push them down they will seat firmly put the top back down screw the burners back in place put the burner caps back on plug the stovetop back in and turn it on.

Too easy a five year old could do it

Remove the existing burner and install the replacement.

First take picture of cooktop. Go below cooktop and unplug electrical and turn off gas valve. Set burner greats aside along with bummer caps. Pull control knobs straight up and off, and set aside. Use 15 torque driver and remove two torque screws from each burner bases. Pull each white igniter up while holding the burner base in place. There is a wire attached to each igniter, separate the wire from the igniter and set aside. Once all igniters are removed, carefully remove all burner bases and set aside. Now lift top cover off. As you’re lifting the cover careful of the igniter wires. Now take another picture to refer to when installing new igniter harness. Notice where the harness plugs in and use pliers to remove the two plug connections from the igniter module. Then remove the rest of the harness from the top of the gas valves. Vacuum debris and clean up tray. Your last photo will be handy, refer to when installing igniter harness. Orient. All burner igniter switches the same on each gas valve. Check for wire clearance on wire harness. Reinstall top, guide igniter wires up through top, relocate burner bases in correct locations. Start all torque screws, leave loose until all igniters are reconnected and placed back down in there holes. Then tighten all torque screws. Reinstall burner caps, control knobs, and greats.
Go underneath and plug in power cord and turn gas valve on. Check all burners for correct operation.

Inserted the grate foot into the spot provided; after consulting the parts manuel to insure I was using the proper procedure.

I do use silicone to help hold the foot but it still won't hold