Models
>
JGC9536BDR15
JGC9536BDR15 Jenn-Air Cooktop - Overview
Sections of the JGC9536BDR15
[Viewing 3 of 3]
Keep searches simple, eg. "belt" or "pump".
Burner Electrode
PartSelect #: PS11744318
Manufacturer #: WP74009336
This is a burner electrode for your oven, range, or stove. This part has a male spade. It helps your burner ignite by creating a spark, producing a flame, and lighting the surface burner. If your burn...
$41.57
In Stock
Screw, 8/18 x 3/8
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$5.42
In Stock
Screw, Igniter
PartSelect #: PS11745563
Manufacturer #: WP8273062
This screw is sold individually.
$7.84
In Stock
X-Large Burner Head with Electrode
PartSelect #: PS2085280
Manufacturer #: 74007736
This is the burner head and electrode for your gas range. If your gas igniter glows but will not light, or if the element will not start or heat entirely, you may need to replace the burner head. This...
$81.10
In Stock
Large Burner Head
PartSelect #: PS2085279
Manufacturer #: 74007735
This part includes the spark igniter.
$85.54
In Stock
Burner Cap
PartSelect #: PS11745641
Manufacturer #: WP8284669
Burner Cap - 6000 BTU
Sold individually.
$55.11
In Stock
Spark Module
PartSelect #: PS11745759
Manufacturer #: WP8286828
This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
$235.22
In Stock
Questions And Answers for JGC9536BDR15
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the JGC9536BDR15
[Viewing 3 of 3]Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Ignitor stopped working on gas cooktop
As others reported, there are 2 torx screws that need to be removed so that the burner element can be removed. One came out with a little effort, the other one did not as it was corroded. After breaking a torx bit, a second torx bit succeeded in breaking off the screw head. This then required a drill to drill out the broken shaft and th
... Read more
en rethreading the screw hole. On to the ignitor replacement. The tiny screw holding the ignitor was corroded and would not come out. It too had to be drllled out and rethreaded. It was a 1/3" #4 screw with fine threads. Had to get it an appliance repair store as the local hardware places don't carry fine threaded screws. Finally got it all put back together after a week. My advice before ordering an ignitor is make sure you can take the current burner off the cooktop first to do the repair in the first place. BTW, the ignitor I ordered came quickly and was the correct part!
Read less
Parts Used:
-
Jeff from Lake Orion, MI
-
Difficulty Level:Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Pliers, Screw drivers, Wrench set
83 of 86 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The ceramic insulator on the burner ignitor cracked & the spark shorted so that the burner would not ignite.
Firts I removed the 2 screws that held the burber in place. Then I lifted the burner up & disconnected the wire that connected to the ignitor. Then I removed the one screw that held the ignitor to the burner. I then reversed these steps, replacing the cracked ignitor with the new one, replaced the screw holding it to the burner, then reco
... Read more
nnected wire, returned the burner to the stove and replaced the two screws that held it. All Done!
Read less
Parts Used:
-
Loren from San Luis Obispo, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
31 of 33 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ignitor did not work
- Removed the cover.
- Removed te two Torx screws.
- Pulled the burner a couple of inches to be able to disconnect the wire.
- Spent a lot of time removing the small Philips screw holding the ignitor. Ended up breaking the ignitor with pliers to be able to put WD40 under the screw's head.
- Treated all screws with a hi ... Read more gh temperature copper paste to prevent oxidation.
Installed the new ignitor with the new screw.
- Reconnected the wire.
- Installed the two Torx screws.
- Voila, it works.
- Removed te two Torx screws.
- Pulled the burner a couple of inches to be able to disconnect the wire.
- Spent a lot of time removing the small Philips screw holding the ignitor. Ended up breaking the ignitor with pliers to be able to put WD40 under the screw's head.
- Treated all screws with a hi ... Read more gh temperature copper paste to prevent oxidation.
Installed the new ignitor with the new screw.
- Reconnected the wire.
- Installed the two Torx screws.
- Voila, it works.
Read less
Parts Used:
-
Didier from LONE TREE, CO
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
24 of 24 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!