All Installation Instructions for General Electric Range JGBS18DET1CC

Interior light needed replaced

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

Parts Used:

Light Bulb - 40W

Leo from TWIN FALLS, ID
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

15 of 25 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Twice I ordered the oven light bulb & each time the light bulb was defected

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Parts Used:

Light Bulb - 40W

Barbara from BELLEVUE, WA
Difficulty Level:
Very Difficult
Total Repair Time:
Less than 15 mins

14 of 23 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burnt burner

Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.

Parts Used:

Burner Head - Medium - 9500

Janine from Wind Gap, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

7 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

I needed another oven rack. It came with two. Now I have three.

I cut the box open with a utility knife and removed the grill. I then opened the oven door and rearranged the two existing racks so that the third one would go in so they all have the same distance between each of them. I slid the new rack into position. It didn't go in smoothly though as I had to push it in and out several times so that it would line up perfectly. Finally in went in all the way. Then I closed the oven door and went and sat down to think about the wonderful job I just did.

Parts Used:

Oven Rack

Frank from N ROYALTON, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

5 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replace Oven light socket and light bulb in kitchen Range

1) Turn off power at circuit breaker panel
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and discard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!

Parts Used:

RECEPTACLE PUSH-IN

Light Bulb - 40W

Ronald from TUCSON, AZ
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set, Wrench set

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broken lines

Super easy!

Parts Used:

Right Front Orifice

Left Front Orifice

David from BONSALL, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burner on stove not working correctly

Order parts and installed - no tools needed - completed repairs less than 1 minute

Parts Used:

Burner Head - Medium - 9500

Trevor from Eldersburg, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

lights blown out

replaced lights in refrigirator and freezer

Parts Used:

Light Bulb - 40W

Gerald from WINTERVILLE, GA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

6 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

F 3 code came on my panel, the oven wasn’t getting to the right temperature

I remove the old thermostat and realized right away it was burned, the replacement was very easy to clip on

Parts Used:

TEMPERATURE SENSOR

Enrico from DURHAM, NC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

no problems it was very easy the parts were a perfect match

first you have close the main gas line, then you remove the nut in the center of each burner then you have to push in the two tabs located in the front part of the stove. one on each side of the out side burners. then you lift the top of the stove. then you will need a wrench to loosen the nuts on the tub. then you have to line up the new ones. put the stove top back on then you have to put the nuts on each burner then you can test for gas leaks

Parts Used:

Right Front Orifice

Right Rear Orifice

Left Front Orifice

Left Rear Orifice

Luis E from HANOVER PARK, IL
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set, Wrench set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven not lighting

Secured the power, Opened the back of the range, and discovered a rodent chewed the wires in half so I striped the ends and wired them back together, the oven works great !!

Parts Used:

TEMPERATURE SENSOR

Charles from SAINT LOUIS, MI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The light inside the oven had burned out

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Parts Used:

Light Bulb - 40W

Catherine from SEATTLE, WA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Light burnt out.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Parts Used:

Light Bulb - 40W

Roscoe G from ROCHESTER, NY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

BASE OF BULB BROKE OFF & WELDED TO SOCKET

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

Parts Used:

RECEPTACLE PUSH-IN