All Installation Instructions for General Electric Range JGBP33CELC

burner would not lite

openend stove top disconnected wire pushed out old sparker inserted new one closed lid game over

Parts Used:

Top Burner Spark Electrode

Glen from Kenner, LA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

23 of 33 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Pies Boiled Over And Baked On Oven Bottom

Removed the two screws put the heat shield off the old one onto the new one put new bottom in and tightened two screws. Done #38. 69 Cost of part with shipping cost included.

Parts Used:

BOTTOM OVEN AND DEFLECTOR ASM

Marjorie from Yucca Valley, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

17 of 21 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven rack missing when I purchased the house

I was very pleased with how quickly the new oven rack arrived and it was a perfect fit. Thanks.

Parts Used:

Oven Rack

Patricia from Houston, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

18 of 27 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Interior light needed replaced

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

Parts Used:

Light Bulb - 40W

Leo from TWIN FALLS, ID
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

15 of 25 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Twice I ordered the oven light bulb & each time the light bulb was defected

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Parts Used:

Light Bulb - 40W

Barbara from BELLEVUE, WA
Difficulty Level:
Very Difficult
Total Repair Time:
Less than 15 mins

14 of 23 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Needed extra oven space

Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.

Parts Used:

Oven Rack

noreen from flushing, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

11 of 15 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven bottom tray would not clean up.Looked like finish was off it

removed two screws and took out bottom tray and put the new one in and replaced the screws.DId it my self.

Parts Used:

BOTTOM OVEN AND DEFLECTOR ASM

Jim from 29 Palms, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

11 of 17 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

loss of spark to two burners, and bent orifice holder

unplugged the old spark module and plugged the new one in. Disassebled and reassembled the new orifice holder.

Parts Used:

Left Front Orifice

SPARK MODULE REPLACEMENT KIT

Kimberly from Leavittsburg, OH
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers, Wrench set

12 of 23 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Change bad/broken igniter on gas stove top burners

Very simple repair with no tools required. Turn off power to stove. Remove grates, remove burner, pull old Top Burner Spark Electrode up being careful not to jerk it up hard - wiggle if necessary, unplug wire from old electrode, plug wire into new electrode making sure it fits snug - if not, squeeze it closed a little at a time until it fits snug, push new igniter into place being careful not to force it and crack the ceramic body. Install burner being careful not to damage the electrode, Install grates. Turn power back on and test to make sure it works. It took me all of 15 minutes to change 2 burner spark electrodes. The only bad thing about this repair is that the shipping costs as much as the parts.

Parts Used:

Top Burner Spark Electrode

James from Kaplan, LA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

6 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

one burner would not light

opened back panel. noted location of colored wires. disconnected wires & removed module. attache wires to new module & attached module to panel. closed up back panel. tested all burners

Parts Used:

SPARK MODULE REPLACEMENT KIT

joe from malden, MA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

7 of 11 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Needed To Replace Burner

Took longer to open the box.

Parts Used:

Small Burner - 5K

Robert K from York, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burnt burner

Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.

Parts Used:

Burner Head - Medium - 9500

Janine from Wind Gap, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

7 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

nylon guide was broke off

took drawer out removed broken guide. It had 1 screw removed it put the new guide in place put screw back in. Put drawer back in stove, It works fine.

Parts Used: