JGB870DET1BB General Electric Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven Lamp Holder Burned
removed two phillips screws. Unplugged electrical connections replaced unit from PartSelect. They sent holder cover and new bulb (surprise). Great store with great directions.
Parts Used:
-
Jack from Okmulgee, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
23 of 28 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Burners and Burner Caps were missing
Very simple repair. I bought the Range without the Burners and Burner Caps. So all I had to do was to purchase the Burners and the Burner Caps and drop them in. Wish everything in life would be that simple.
Parts Used:
-
Alejandro from Newark, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
31 of 54 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner would not lite
openend stove top disconnected wire pushed out old sparker inserted new one closed lid game over
Parts Used:
-
Glen from Kenner, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
23 of 33 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bottom oven wouldn't warm up
Remove the door for easier access. Remove the fan cover from the back of the oven (about 6 Phillips head screws). Remove the bottom cover (2 5/16" screws). Lift the cover from the back and slide out. Remove the old igniter (2 5/16" screws). Pull the oven away from the wall. Remove back cover (3 5/16" screws). Unplug igniter, feed wiring through the oven. Install new igniter.
Parts Used:
-
Mike from SAYREVILLE, NJ
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
13 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner grate bumpers/feet missing
-
Raymond from Waukegan, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
13 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
This was not really a repair. Just replacement. The burner caps get discolored rather quickly and nothing removed the stains. I'm thrilled to have replacements on hand.
Removed the old caps, replaced them with the new ones.
Parts Used:
-
Elizabeth from MECHANICSBURG, PA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
9 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven post mini explosion sounding
the flame spreader through the years, developed a hole above the glow coil causing the above trapped gas between the oven pan and spreader to ignite. by replacing the flame spreader the problem is gone and is now working properly. thank you, parts select for being there when i needed the part and also being reasonably priced. mike marino
Parts Used:
-
Mchael J. from Chesterfield, VA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
13 of 22 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner would not light properly and flame uneven around the burner
determined that the top of the burner was melted and malformed. Repair was simple: lifted off the damaged burner and slipped the new one in place.
Parts Used:
-
Bret from South Haven, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
9 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Our burner caps had started chipping.
Was able to see the exact part with easy to read schematic so I knew I was ordering the right part. Then just switched out the old for the new. Looks like a new cooktop except for the scratches in the stainless, but we are working on that! Thanks!
Parts Used:
-
Kim from Santa Rosa, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
12 of 20 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Change bad/broken igniter on gas stove top burners
Very simple repair with no tools required. Turn off power to stove. Remove grates, remove burner, pull old Top Burner Spark Electrode up being careful not to jerk it up hard - wiggle if necessary, unplug wire from old electrode, plug wire into new electrode making sure it fits snug - if not, squeeze it closed a little at a time until it fits snug, push new igniter into place being careful not to force it and crack the ceramic body. Install burner being careful not to damage the electrode, Install grates. Turn power back on and test to make sure it works. It took me all of 15 minutes to change 2 burner spark electrodes. The only bad thing about this repair is that the shipping costs as much as the parts.
Parts Used:
-
James from Kaplan, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
6 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The griddle needed to be replaced
Lifted the old one off and placed the new one on. Fits perfectly and looks great!
Parts Used:
-
brigitte from vacaville, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
6 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original burner cap was chipping; must have been dropped somewhere along the line.
New burner cap replaced old; just placed over burner; no tools required.
One suggestion: burner cap should have been shipped with thicker bubble protection (easy to do). It was minimally wrapped and placed in a thin, bubble envelope, risking damage in shipping process. Luckily, the burner arrived in tact and usable.
One suggestion: burner cap should have been shipped with thicker bubble protection (easy to do). It was minimally wrapped and placed in a thin, bubble envelope, risking damage in shipping process. Luckily, the burner arrived in tact and usable.
Parts Used:
-
Mitzi from Briarcliff Manor, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
8 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven light did not work
Turned off power to the oven, Removed the oven light housing, installed new housing, turned power on and walla.
Parts Used:
-
Howard from Rio Vista, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
9 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
wire connection to socket was bad
Disconnected the old socket ( 2 srews ) removed the two wires from the old socket, reconnected them to the new socket and reinstalled the lamp.
Parts Used:
-
David from Gansevoort, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
6 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burnt burner
Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.
Parts Used:
-
Janine from Wind Gap, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
7 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!