Models > JGB850DEF2BB > Instructions

JGB850DEF2BB General Electric Range - Instructions

All Instructions for the JGB850DEF2BB
1 - 15 of 63
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven sensor was not holding temperature range.
Per the instructions included with part.
Parts Used:
Temperature Sensor Kit
  • CHARLA from NEW BRAUNFELS, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
44 of 75 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven Lamp Holder Burned
removed two phillips screws. Unplugged electrical connections replaced unit from PartSelect. They sent holder cover and new bulb (surprise). Great store with great directions.
Parts Used:
Oven Light Housing
  • Jack from Okmulgee, OK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
23 of 28 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
defective temp. sensor
Removed oven from cabinet. unblug old sensor pluged in new and reinstalled oven. Esay repair though wish oven was designed so did not have to pull itout of cabinet which requires disconect electric cabel
Parts Used:
Temperature Sensor Kit
  • Armand from COVENTRY, CT
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
19 of 26 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
When baking at temps > 400 the oven would beep with an error code F5 and shut off
I downloaded the installaion manual from the web for this model. First htings first, I located the circuit breaker for the oven and turned it off. Removed the lower trim piece from the bottom, next lifted the oven door off its hinges and set it to the side. I then wrapped a couple of small towels around the hinges for the door as per the manual (the hinges can pinch a finger). I then removed the four screws which secured the oven into the cabinet. Next I slid the oven forward allowing me access to the rear. I removed the pieces from the rear to gain access to the sensors connector, and unpl;ugged the sensor. Went around to the front and unscrewed the 2 screws securing the sensor and removed it. I then installed the new sensor, replaced the rear covers, slid the oven back into the cabinet, secured the four screws, snapped on the lower trim, remounted the oven door, and turned the breaker on. Oven working fine now.
Parts Used:
Temperature Sensor Kit
  • Jack from Cypress, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
16 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven was not reaching or maintaining temperature.
Took off oven door and removed racks. Removed the cover on the back side (5 screws removed with nut driver) Pulled sensor out the front side of the oven. Threaded the new sensor through and put all back together.
Parts Used:
Temperature Sensor Kit
  • Raymond from Madrid, IA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
14 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner grate bumpers/feet missing
Hi temp (900 deg) engine gasket adhesive on numbs and press in. DONE !
Parts Used:
Rubber Feet
  • Raymond from Waukegan, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
13 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
This was not really a repair. Just replacement. The burner caps get discolored rather quickly and nothing removed the stains. I'm thrilled to have replacements on hand.
Removed the old caps, replaced them with the new ones.
Parts Used:
Burner Cap Burner Cap - Black - Medium - 9500 BTU Burner Cap - 5000 BTU - Black Burner Cap - 15K
  • Elizabeth from MECHANICSBURG, PA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
9 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner would not light properly and flame uneven around the burner
determined that the top of the burner was melted and malformed. Repair was simple: lifted off the damaged burner and slipped the new one in place.
Parts Used:
Burner Head - Large - 12K
  • Bret from South Haven, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
9 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Our burner caps had started chipping.
Was able to see the exact part with easy to read schematic so I knew I was ordering the right part. Then just switched out the old for the new. Looks like a new cooktop except for the scratches in the stainless, but we are working on that! Thanks!
Parts Used:
Burner Cap Burner Cap - Black - Medium - 9500 BTU Burner Cap - 5000 BTU - Black
  • Kim from Santa Rosa, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
12 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original burner cap was chipping; must have been dropped somewhere along the line.
New burner cap replaced old; just placed over burner; no tools required.

One suggestion: burner cap should have been shipped with thicker bubble protection (easy to do). It was minimally wrapped and placed in a thin, bubble envelope, risking damage in shipping process. Luckily, the burner arrived in tact and usable.
Parts Used:
Burner Cap - 15K
  • Mitzi from Briarcliff Manor, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
8 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The griddle needed to be replaced
Lifted the old one off and placed the new one on. Fits perfectly and looks great!
Parts Used:
Griddle
  • brigitte from vacaville, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven light did not work
Turned off power to the oven, Removed the oven light housing, installed new housing, turned power on and walla.
Parts Used:
Oven Light Housing
  • Howard from Rio Vista, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
9 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
wire connection to socket was bad
Disconnected the old socket ( 2 srews ) removed the two wires from the old socket, reconnected them to the new socket and reinstalled the lamp.
Parts Used:
Oven Light Housing
  • David from Gansevoort, NY
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
6 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burnt burner
Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.
Parts Used:
Burner Head - Medium - 9500
  • Janine from Wind Gap, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
7 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed To Replace Burner
Took longer to open the box.
Parts Used:
Small Burner - 5K
  • Robert K from York, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JGB850DEF2BB
1 - 15 of 63
Back to Top