JEM31SF001 General Electric Microwave - Instructions

The microwave had been working fine until one day when the timer counted down but the heating motor (or whatever you call it) would not come on. So the timer would count down but nothing inside would get hot. I did not know what it was for sure but decided to take it apart and look. Once I had the control panal off, I found three small wired switches inside. One of these switches appeared to have shorted out. So I searched online and found Partselect.com. I found a matching switch , ordered it (arrived in couple days), put it in, and VOILA it works! Thanks Partselect.com.

I've been fixing and taking things apart since I was a kid. I hoped that it was a bad switch in the door. Got out my test meter and check the 3 different switches. All 3 tested good, but one was a bit hit and miss. It would work if the microwave was on its side and wouldn't when it was set flat. I found the switch online and installed it. Took care of the problem.It was a whole lot cheaper than buying a new microwave. Thanks! Bill Brown, Fridley, MN

The switches are not the problem! The problem is in the tolerences of the latch housing. I have ordered two new housings (Upper & Lower) and will see if the tolerences are closer. If not I will try epoxying a shim to the plate that operates the microswitches. The other option is to file the mounting slots of the housing to allow adjustment, which would be iffy,keeping them from moving with use. The exploded drawings really need to be clarified. The scale is way too small. It was extremely difficult to pick out the individual parts of the mechanisiam.

All electrical worked (fan, lights, control panel) door switch was broke. Pulled the oven out. Took out two big screws from the cabinet above. (be careful not to drop oven)Set the oven on kitchen counter. Took off five screws that held the vent cover. Removed vent cover. Took out one screw that held the control panel. Lifted, turned and slid the panel into the space below so I could get to the upper door switch. Replace door switch and re-assemble.

Had trouble isolating the problem, so I had a repairman identify the problem, then I ordered the part and replaced it myself.

Removed screws holding the grill in place. Removed air filter, removed screw holding plate under the filter in place. Reached in under fan cowling to find the thermostat cut-out. Disconnected the two wires. Put the new thermostat in place. Replaced screws plates and filter in reverse order.

Took cover off, noted the two side by side switches easily visible and we hought one of these was responsible. Then son noted a third switch at the top of the plastic assembly which inserts at an odd angle. When it was inspected signs of a previous short showed up with burnt contact points. Reinserted at same odd angle as there were guide holes, closed things up and oven worked 100%. Great prompt service and great website!! We will use you again

Primary door switch was shorted and blew the fuse when the oven was plugged in. Replaced primary door interlock switch.

took of cover removed switch and replaced with new one

I removed the unit from the wall removed the top two screws holding the panel above the door I the two screws holding the control panel removed the three switchs I found the top one to be blown and replaced it

Removed control panel first then removed bracket holding door switches 8 screws total very easy fix ????

After researching on line and watching installation videos, ordered all three switches and installed. Disassembly of microwave was simple, removing the bracket holding the switches was a little tricky, it sits behind a metal post and you have to angle and wiggle it out. One note of caution when replacing all three switches, be sure to install correct switch in correct location. Had two of one style switch and one of a second style, and put one in wrong place, causing microwave to power up again when door was opened. After thinking it through and doing a second disassembly, and double checking installation instructions, corrected problem and microwave now works fine.

First, potatoe burned up in microwave. Microwave
was dead. Took off cover and found maintaince repair pamphlet in envelope. Schematic showed one shot thermostat for fire. Ordered thermostat from you and installed it. Works fine.

Simple removal of old film - scraped one corner and it pulled right off. New film was a bit difficult to install as it had been folded in half for shipping. There was a large crease in the middle which made it hard to flatten out on the door. The adhesive was limited on the crease as well. I can still see the crease in the film on the door after installation. Dissapointing - but it works. I recommend the film not be folded for shipping in the future.

it was easy, one in one out.

Most of the effort is simply getting the oven out of the built in enclosure and the sheet metal off. This take about 15 minutes then you have to remove the two screws (not handy location) that hold the door latch/switch assembly so you can remove the switch. I did this BEFORE ordering so I could test the switch (it was charred) and verify the part needed. WATCH OUT - some ovens use a normally open an some a normally closed version of this switch - you have to get the right one. I checked several suppliers that were showing the WRONG switch for my model. PartSelect had it right. Once I received the switch I had it on and the oven installed and running in less than 30 miutes. Working fine since then...