Enter the code TAKE10OFF at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on May 28 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
I simply remove the broken knob just like I do when cleaning. To place the new knob, I matched the flat part of knob opening with the flat part of the shaft, returning to off position.
Turned the breaker off, I removed 2 screws securing the range top to the range, opened the top and secured it in the up position, Removed the 2 screws securing the element ,one at a time I swapped the quick connectors from the old element to the new and repeated the process in reverse. I save over $100.00 in labor, plus most companies get you for a trip charge. It was easy!!
Thermal switch is integral to element and can not be changed, must replace entire element.
Turn off power. Removed front two screws above oven door jamb and lifted the top. Removed the bracket that holds the element against the glass top and removed the element. Moved brackets from old element to new one, aligning to same numerical position and then moved wiring to new element. Slide new element under bracket and reinstalled single screw. Replaced top and screwed down. Turn on power and test .
Having replaced 3 knobs already, I was still experiencing splitting of the knob shaft where it fits over burner control shaft
To reinforce 5 knobs after replacing 3 knobs earlier using the "simple" replacement of knobs: My 19 year old daughter mixed a 15 minute two part epoxy glue and coated the outside of the plastic knob shaft (first placing a q-tip in the center of the shaft opening to protect from glue entry into knob engagement channel). She then wrapped the wire in a close spiral so each turn touched the previous one (like a spring), leaving the wire ends long enough to twist around knob ears to hold firmly in place during cure of glue. She then coated the outisde of the wire turns with more epoxy to encase the wire and secure wire in place. After curing, she cut the wire ends off so they were flush with knob shaft and installed knobs on burner stems. Hopefully a permanent solution as you shouldn't have to modify replacement parts.
double coil which center coil had burned out on glass top range
Unplug range and remove back panel (4 screws) unplug top burner plugs (2). Open oven door and remove 2 screws from under front of top. Pull top out and up to unhook from back. Remove top and lay cardboard on top of range. Flip over the ranges glass top unit and lay on cardboard. Remove screws from steel bottom and remove from top. Flip over steel bottom with burners attached. Remove attaching clips for burner and unscrew them from the burner then reinstall in new burner in the same place as old burner. Lay new burner on top of old burner and remove one wire at a time, transfering it to the matching plug on the new burner. When wiring is done remove old burner and attach 2 clips to steel backing plate. Vacuum off the glass top and reinstall the steel bottom to the glass top. Flip over the top, remove cardboard and slide top into back of range top and lower into place. Attach 2 screws under front. Reattach the tops plugs at the rear and reattach the back panel. Plug in range and slide back into place. Test units and all other burners. Done...
Ordered new knobs from part select ,they arrived very quickly. I took off the metal clips that where in the old knobs.(these clips where still on the metal post because the broke away from the plastic knobs.) Then I just pushed on the knobs nothing to it.
Shaft of original burner knob had split and no longer controlled the selector shaft
The broken knob had previously been removed. I grasped the replacement knob between my thumb and forefinger, held the knob in a vertical position and pressed it down onto the selector shaft. The quality control supervisor (otherwise known as "the wife") examined the project and issued a certificate of acceptance. And then cooked dinner.
3 months after my 5 year warranty ran out, one of the elements on my wife's maytag cooktop "popped". I was curious to see if I could fix it myself and ran across partselect.com via google. Their step by step instructions for determining the source of the problem (i.e. either the element or the control was bad) led me to realize that the element was bad. I ordered a new one -- which arrived in 3 days! It was very easy to replace the element, since I had already taken the glass cooktop off of the range during the testing phase. Thanks partselect.com!
Turned off power at circuit breaker. There is a panel on the underside of the stove top with four hex head screws. Removed it to give access to the switches beneath the knobs. A socket set was useful here. Identified the switch that was shorting. Detached the wires connected to that switch. They are all quick connects, but some are tight so pliers helped here. (It is a good idea to keep track of which wire is supposed to go where. Also there is a wiring diagram available somewhere on this site.) Removed the switch by taking out the knob on the top and loosening the two Philips screws on either side of the switch stem. The switch came out easily after that. Put in the new switch, reattached with the Philips screws, and replaced the wire connection. Replaced panel and turned power back on. Turned on burners to ensure proper operation.
1. tripped circuit breaker for stovetop 2. pulled the stove top out of its cabinet. 3. turned in over carefully due to the glass cooking surface. 4. used 1/4 inch nutdriver on cordless drill to remove all the screws holding the lower cover in place. lifted cover off without removing completely as power wires still attached. 5. did continuity test on burner and found it open circuit while all the other 3 burners had continuity. 6. removed defective burner by removing two more screws and saw element was fried on the cooking side. 7. wrote down all part numbers and put it all back together. 8. changed the burner out when new one arrived by repeating steps 1 thru 6. Pay attention to the correct wiring setup. Do one wire at a time to make sure you don't mess up. MAKE SURE THE CIRCUIT BREAKER IS TRIPPED BEFORE YOU KILL YOUR SELF.
Have a tall one to celebrate the savings of two repair man call out fee's of minimum $60 each time and paying list price for the element. You probably just saved yourself $150. Tom in Steinhatchee