JDB1080AWS Jenn-Air Dishwasher - Instructions

1st: Unscrewed the inside of the door (actually hex screwdriver needed).
2nd: Removed broken part (one side of handle latch (which is plastic) was broken.
3rd. Had to disconnect two electrodes that were attached to the part that held the handle (there are two small prongs that you need to push back to remove these)
4th. In order to place the handle on the groove, you need to pull apart the bottom of the housing piece (it looks like it would be a hinge, but you just pull it apart)
NOTE: Make sure you have another person hold the top portion when you pull this apart because it has a spring and will come completly apart. This happened to us and it was a pain to get it back together.
5th: place the smaller "clamps" plastic pieces in the grove and then it should slide down into the groove, which will also seat the outer "plastic clamps" into the grooves.
NOTE: It seems like the repair part was built to reinforce this part of the handle, since this was the part that broke before. It is now reinforced with a little metal rod on each side.
6th: After all that, you need to place the two electrodes back on the piece.
7th: Hold it in place and put the inside of the door back on (start a screw on one side and then go to the opposite side. This will help to align the screw holes).
8th: After I put it all back together, I turned it on to make sure it worked ok.

1st, shut off the breaker for the dishwasher.
2nd, opened the door and removed all of the torx screws holding inner door to outer door.
3rd, placed inner door up and held it out of the way (closed inner door through/around latch tab and folded up a piece of paper, threaded it through latch tab hole and placed a small piece of masking tape around the paper to hold door out of the way - this made the entire job easier, because you do not need to hold the door out of the way anymore).
4th, removed broken latch/handle assembly (carefully - it is always a good idea to collect/save broken pieces to piece together the "puzzle" in case you need to improvise. Removing the metal clip attachments is tough, but much easier now that the inner door is secured out of the way. They cannot simply be pulled straight out. You should use a gentle back and forth wiggle motion in a T-shape. Meaning, wiggle back and forth 1-way, and then the other way (perpendicular to the first way) - this should get them separated. Be patient with this procedure - it will work fine and you won't get frustrated.
5th, look at the situation to determine exactly what went wrong/broke specifically (I was extra screwed, because 1/2 of each of the "U" shaped tabs that hold each side of latch assembly in place were broken - as well as the tabs on the latch assembly. These U-shaped tabs were/are actually part of the plastic outer door. Specifically, they are on the inner side of the plastic control panel display. I could have replaced this part too, but I was trying to do as inexpensive a repair as possible.
6th, So - I found 2 nut/bolts in my toolbox (probably 1/8" in diameter - 3/4" in length - I used flat head. Be careful in your selection of bolt length - the least amount sticking out the front of the dishwasher - the better). I drilled 2 holes - in the exact location where these inner door tabs broke off - and entirely through to the outside of the outer door - yes, all the way through. We are talking about drilling through less than 1/4" of plastic - simple. I made sure that I would not be drilling through any lighting display or really important pieces. The holes ended up being situated in plain plastic locations - not interfering with any functions. Be careful in your selection of drill bit size - you want the bolt to fit through the hole obviously, but you don't want the bolt to have too much wiggle room - because it will be functioning as your new tab - that should have as much structural integrity. So, I recommend drilling a hole that is just big enough that you have to use a screwdriver to thread the bolt into the hole.
7th - I connected the clips into the new latch assembly - somewhat easier than separating the old one.
8th - I placed the new latch/handle assembly into its proper location (resting on the 1/2 mounting tabs that remained on the inner door).
9th - I then used a small flat screwdriver to thread the 2 screws in place (yes, screw head on the inside of the door - to function as a tab - the edge of the screw head will hold down on the latch tab ends). I had to tilt the latch assembly forward, to allow just enough clearance to get my small, thin flat head screwdriver in there (on a slight angle, but that's ok). Thread it through until it gently snugs down onto the latch tab.
***You can do better than I did if you want to go the extra mile*** Find a small, thin piece of sheet metal or plastic. Drill a hole just big enough for the bolt threads to slide through. This sheet should be cut to the following specs: a rectangular shape just big enough to span across the tab you made with the bolt - onto the inner door tab that it still not broken (the drilled hole to fit the bolt threads through on one end). It is added structural integrity to even better hold the new latch assembly in place. Think of it as a bridge that spans the tops of the U-tabs.
10th - After screwing the bolts through until just enough to snug down on the latch assem

This repair was very easy. First, I opened the dishwasher, removed the screws (they are torx) and removed the old handle assembly. I removed the inner liner from the door, and to do that I had to pull out the electrical wires. I turned off the power, always a good idea. I should have marked the polarity on the plugs before removing them, since you can put them back on wrong (and I did).

I also used caulk to hold the assembly on the bottom, since the cheap plastic molded forks holding the assembly on had broken. Most of the holding force comes from screws at the top. The caulk provides just a little adhesion, and will be easy to remove if the handle should need to be removed again--which I consider unlikely.

This was a very easy repair. Before I did anything, I flipped the breaker for the dishwasher and tried to turn the dishwasher on to make sure it had no power going to it. Once I was certain the power was off I removed the hex screws (there are 11) on the inside of the door panel using the hex screwdriver. Lifting and holding the inside panel up, I then used the pliers to pry the old latch assembly out of its metal prongs. Then I replaced the old latch assembly with the new one, pushing the metal prongs (by hand) into the slits of the new latch assembly. Last, I lined everything up and screwed the door panel back in place. I flipped the breaker back on and activated my child lock to make sure I had power. The handle worked perfectly. Quick and easy fix!
I ordered the part with 3-5 day delivery and actually received it in 2 days! I'm extremely pleased with my partselect.com experience and highly recommend using them for all your appliance parts needs!

i ordered the parts on sunday night at about 9pm. the parts arrived on tuesday afternoon! i removed the screws on the inside of the door, then removed the latch assembly and unplugged the two connectors. i then plugged in the new latch assembly and replaced the screws. i accidentally ordered two parts i did not need and received an email twenty minutes after i asked how to return the unneeded parts descibing the return process. i have already told three people how awesome your company is. anytime i need appliance parts i won't look anywhere else. you have a customer for life!! thanks for everything.

I could not reach the heater element nuts from under the dishwasher so had to pull out the dishwasher. I removed the screws around the front of the dishwasher and pulled it about half way out before the water inlet pipe and the electrical wires stopped me. I shut off the water, unhooked the copper pipe, and unhooked the electrical wires (shut off circuit breaker first). Pulled the dishwaser out so I could remove the element nuts and wires to the element. Removed the old element and installed the new one - the old nuts would not fit. I went to a local appliance parts store and found that my element is no longer made. I had the correct replacement element but you need to order the nuts also. Luckily, the local store had a small brass nut that worked. Reattached the electrical wires to the element, pushed the dishwasher half way in, reattached the water inlet and electrical wires, pushed the dishwasher all the way in and scewed back into the cabinets. All is well now and the dishwasher is working much better.

Ist Repaired a hole in a rubber hose under the sink. 2nd Removed the 10 foot drainage hose with a regular screw driver (1 clamp at each end of the hose).
3rd Removed the insulation and replaced with the new after disinfecting the entire top and sides of the dishwasher with bleach. This eliminated all bad odor etc. only had to remove 2 plastic brads, 1 on each side of the unit.

Done and no leaks.

The spring mechanism is on the side, so you have to pull the dishwasher out onto the floor. To do that, you have to remove the floor molding (preferably without breaking it) and remove the base coverings (painted metal plates on the bottom of the washer. Unscrew the side gasket plates on the side of the dishwasher (just inside of the door) where it attaches to the cabinet and the screws in the braces at the top (inside the door) where it attaches to the counter top. Now you will be able to slide the washer forward to look at the sides where the door springs are. Depending on the floor, you may have to raise the washer's front feet. They screw up. As you pull the washer forward be careful to not mess up the insulation which drapes over the top and sides. You only need to come out 1/3 of the way to see the sides where there is a plastic wheel at the forward bottom corner. As you move the door up and down you can see the hook where the cable goes and further up the side you can see several notches where the spring goes. Hook the cable and bring it around the wheel and attach it to the spring. To reinstall, just follow these directions backwards. Good luck.

After finding out that the impeller shaft was stripped (plastic) I quickly found the correct replacement on partselect.com by using my model number.
You do not have to remove the dishwasher, if you know what is wrong. But, throw the breaker switch and turn off the water! After removing the spin washer arm, Undo all of the torx screws and pull out the plastic filter looking plates along with the center plastic water jet. This jet provides water for the upper washer assembly. You may have to pop that upper assembly out to protect it from damage.
The black impeller should just pull out if the plastic shaft is stripped. Otherwise, unscrew the small torx head and remove the impeller. You can remove the blade at this time and unscrew the plastic shaft by unthreading it while keeping the motor from spinning. (I shoved a screw driver underneath the dishwasher through the motor. Also the motor is just floating on the rubber gasket and can easily pulled out to accomplish this task. It's heavy and has a plug attached to it. You'll see where you can shove the screw driver. This comes in handy while installing the new shaft, because it is metal. Which is a great, long awaited upgrade for the Maytag Quiet Series. Once you find which shaft to use, (which correct inner thread, course or fine), install it with the great directions that come with the part. Putting all the stuff together is not as bad as one would think, there is only one way for it to go back together. After installation is complete, turn water and breaker switch back on. Run a cycle and listen for the washing cycle against the wall of the washer. If you cannot tell the difference, you can unscrew the white lock arm and insert it into the door. Turn it on and watch how a dishwasher works. Get ready to get a little wet. Towels!

The original brackets that hold the water distribution manifold to the back and top of the tub came off the "X-shaped" plastic posts on the tub walls. That caused the upper wash arm to sag down into the travel of the upper dish rack and was broken off when the rack was pushed in.
I bought 2 new brackets and a new wash arm. The new brackets had a smaller aperature than the originals and fit tightly onto the plastic posts, holding the manifold firmly in its proper location. Replacement of the brackets and the new wash arm took less than ten minutes and required no tools!

Not being very computer literate, the most difficult part of the entire venture was navigating your web site. But I finally found the part I needed. I paid on line with a credit card, and received the part within a few days. I popped it in the dishwasher, and it took three days before my son noticed it.
He was surprised and I was proud to say " I ordered it on line."
All's well that end's well.
I would difinately use your service again.

I unscrewed the door panel. removed the plastic cover protecting the dispenser. unscrewed the dispenser (6 screws). I removed the old dispenser and put the new one on and put it all back together. It was pretty easy.

remove shelf install ball bearings in new ball cage click ball cage into slides re-install shelf piece of cake make sure you have all the ball bearings when ordering the cage they dont come with it 4/cage

disconnected unit (electrical, water, and waste) un mounted from countertop, removed from under countertop, unscrewed hose clamb, cut off wire tie. Attached new hose and wire tie (not included) reversed above steps. Done in about 15 minutes

This isn't a how to fix it....it's what part was bad. I had originally contacted the local Maytag repair center and the owner swore up and down that our problem had to be the thermostat and not the heater. He said he had only replaced maybe 5 heaters in 15 years. But our heater looked like heck, with hard water deposits and all, and it wasn't that old, but we went ahead and ordered the thermostat from PartSelect, which came in a day. The problem wasn't the thermostat, so we ordered the heater from PartSelect (again, only one day delivery) and our dishwasher is working again. The heater coil actually had a hole in it from some sort of corrosion. My 18-year-old son did the repair job in a jiffy.