HTG16BBMCRWW Hotpoint Refrigerator - Instructions

I applied some tips learned by reading other reviews. So before I started I grabbed my trusty vise grip pliers and a small screw driver. I locked onto the switch actuator, the part that the refrigerator door pushes in, with the vise grips and pulled on it just hard enough to get the screw driver inserted in the right side to push in the catch clip so the switch could be pulled out further each time the catch clip was depressed to the next detent. Then I used the screw driver on the left site to encourage the switch past the detents on the left and very quickly the switch was out of the mount. The wires from the refrigerator pulled out with the old switch. I unplugged the old switch from the wires and plugged in the new switch and shoved the new switch back into the mount, wiggled it a couple of times to make sure it was secure and the job was done. Once I applied the vise gripes at first, the whole job took less than a minute.

When the cover came to my apartment, I crossed my fingers that the piece would fit . Well, within 5 minutes the old cover was out and the new cover in. And it looks better than new! Finally, I don't have to hold my vegetable drawers up with a D battery!

Unplugged refrigerator.Checked that new gasket was the right size for freezer.Opened freezer door and lifted inside edge to access screw's. Loosened top screw's and screw's half way down each side and pulled gasket out. Installed new gasket into slot where old gasket was and tightened screw's across top and the first couple down side's.Lifted edge of old gasket and loosened screw's holding remainder of old gasket in place and finished removing old gasket.Finished putting new gasket in slot and tightened remaining screw's. The reason for only doing gasket half at a time is to keep the door square and not getting out of shape. If new gasket is warped when removed from shiping box run under hot water or soak in hot water until more flexible.

No tools required! The replacement pan cover was shipped and arrived within 3 days. I pulled out the drawers, then the cover. Slipped the new one in, slipped in the drawers and it was finished.

Poped out with screwdriver the old swithch and unplugged the two wires. Plugged in the wires to the new swithch and pushed it back in the hole where the old switch was before.

I took the broken part off the bar, put the new part on the bar, snapped it into the fridge, threw the old part out, opened the fridge admired my work, while I was ther I grabbed a beer....couldnt have gone better.

Simple install. .

Removed 2 vegetable drawers and phone book and cd case supporting the vegetable drawers. Removed food items sitting on top. Lifted out cracked pan cover and put in place the new one. Reinserted all items originally removed except for phone book and cd case. It was a perfect fit and probably the easiest repair job I have ever done. I do not know why I waited 2 years to find the part.

While the switch did last for 9 years, the design is poor due to the failure mode. The failure should be to fail off or not able to turn on the lights which would be inconvenient but would not warm the refrigerator contents. Arcing at the contacts eventually caused the switch to "weld" closed. It is not obvious that this is occurring so it took some time to recognize why the temp inside the ref was high while the freezer was OK. Replacing the switch was easy once it was recognized as the problem. All that was required to replace the switch was to remove the screws holding a fiber cover and then pulling off the aluminum cap which covered the switches. Unplug the switch an squeeze the keeper on the switch to release it and pull down. Pop the replacement switch in place and plug the wires harness back in. All in all it took much less time to replace than it has to write this up. T Pope

The existing light switch was very hard to remove. I ended up having to grab it with a pair of pliers and pull it out. Once it was out, it was very easy to put in the replacement and it seems to be working fine.

I purchase a new veg. shelf cover and an additional shelf for my refrigerator. The parts came quickly and I am very happy with the new parts. I have posted your web site on my favorite for future use.

first i removed old gasket then pressed in new one very easy repair

I opened the refrigator door and inserted the shelf where the missing one shoud have went and I remoed the old Vegetable bin cover and replaced it with the new one.-----JOB DONE !

as described, I used a thin screwdriver to wedge in and pull down existing, broken switch. I was able to pull it down about a 1/4 inch, but wasn't quit able to disegage it until I gripped it with pliers. I then pulled it out, unplugged the old switch, plugged in the new switch, and carefully tucked the wires back into the fridge and snapped the new switch into place.

10 minutes total.

I pull the old one out, and put the new one in.