Parts That Fix General Electric Washer GTWN2800D0WW Leaking
Leaking is a commonly reported symptom for the GTWN2800D0WW General Electric Washer, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your GTWN2800D0WW General Electric Washer that will fix Leaking. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
The drain hose is black in color and made of flexible material. This is a part for your top-load washer. The hose measures 57 inches long. This part moves the water out of the washer and into the drain. If this parts cracks or becomes damaged it will leak during the drain cycle of your wash and you may find water on the floor. To access the hose, you will need to move the washer away from the wall to get to the back of the appliance. There will be two screws holding it in place that will need to be removed.
Replacing your General Electric Washer Drain Hose
Customer Repair Stories
Hose would not seal at rear of washer.
-
Charles Wayne from Forest Hill, WV
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
Purchased used washin machine w/o drain hose
-
Daniel from Oxford, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
The main tub seal is located between the transmission and the outer tub. Its the primary water seal in the outer tub for the transmission-shaft. If your washer is leaking during the fill cycle, or at agitation time, your tub seal may need to be replaced. You can check if the tub seal needs to be replaced by watching that area during an actual fill cycle. Take off the front panel, or if it is a front-loading washer, the rear panel. Without touching the washing machine, observe the place where the shaft of the transmission comes into the tub and the weep holes at the housing of the rear bearing. If there is water leaking, the tub seal is at fault. NOTE: This seal is difficult to replace and should probably be installed by a qualified technician.
Replacing your General Electric Washer Tub Seal
Customer Repair Stories
Leak
-
Tom from VERMILLION, SD
-
Difficulty Level:Really Easy
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Socket set
Would agitate, but not spin, leaving clothing soaking wet.
-
Anthony from DEKALB, IL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
This replacement inlet drain hose connects your washer's water pump to its tub. This hose is seven and a half inches in length and only two inches wide.
Replacing your General Electric Washer Pump to Tub Inlet Drain Hose
Customer Repair Stories
water leak in hose
-
Steven from Holbrook, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
Water was leaking
-
Christine from Tempe, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
This split ring is supplied by the original equipment manufacturer, and it is designed to secure the tub bearing in washing machines. It is a circular metal ring, with an outer diameter of 2 inches. The ring has a split or gap, which allows it to expand and contract for easy installation and removal. It is typically located on the inner side of the washing machine outer tub, where it provides stability and prevents the washer from excessively shaking during use. It is normal for the split ring to become worn, corroded, or damaged due to age, exposure to moisture, and excessive stress. A faulty split ring will lead to a noisy, unstable washer and eventually cause the tub assembly to fall out of alignment. Remove the washer panels to access the outer tub and split ring. Carefully detach the damaged split ring from the tub and position the new split ring in its place. Ensure that it is properly aligned and securely fastened before reattaching the panels.
Replacing your General Electric Washer Split Ring
This is a tub bearing and it is meant to work in conjunction with your washing machine. The purpose of this part is to aid in keeping the inner tub of your washing machine spinning smoothly during a wash cycle. The most common reasons for needing to change your tub bearing is if your appliance is noisy or shaking/moving during the wash cycle, another common symptom is leaking water. This part is sold individually and measures to have an inner diameter of roughly 1 inch, and an outer diameter of roughly 2 inches.
Replacing your General Electric Washer Tub Bearing Washer
Customer Repair Stories
Noisy washer, especially while spinning.
-
Olle J from Albert Lea, MN
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers
The machnica had recently developed a rumble during the spin cycle
-
Fred from Murphy, TX
-
Difficulty Level:Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Socket set, Wrench (Adjustable), Wrench set
This part is the replacement water fill nozzle for your washer. It is white and tan in color, made of plastic, and is approximately 7 inches long and 4 inches wide. The water fill nozzle is also known as the water inlet assembly and directs the fill water into the tub. Over time the nozzle can become cracked and damaged, and this can cause it to leak. A damaged nozzle will need to be replaced. Be sure to disconnect the water supply to the washer before you begin this repair. You should also determine if any of the other parts that transport water into the washer are leaking, including the water inlet hose, and if they need to be repaired as well. This part is sold individually and is a genuine OEM part.
Replacing your General Electric Washer Water Fill Nozzle
Customer Repair Stories
Water dripping into the washer when washer was not in use
-
Beata from STUART, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
Water leaking from filler hose outside of tub
personnel at part select were very knowledgable about detailed part and the overnight service was right on time.
I would recommend part select for your next appliance parts needs.
-
Paul from Talihina, OK
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
The tub dampening straps support the wash tub and reduce vibration by keeping the tub at the center of the cabinet. If your washer shakes and moves, or is making a loud banging noise during the wash cycle, the washing machine tub could be off-balance, meaning one or more of these straps may be loose, or broken. Other symptoms include: the washer leaking, not agitating, or pumping but not spinning. These straps are sold individually. However, we recommend that you replace all 4 straps at the same time. It is also recommended that you check the tub for cracks where these straps mount.
Replacing your General Electric Washer Tub Dampening Strap
Customer Repair Stories
Noticed 3 straps were broken when we replaced the hose
-
Christine from Tempe, AZ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Socket set
loud noise upon aggitation
-
Robert from Covington, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
This tub bearing goes in your washing machine. You will find it on the bottom of the outer tub, where the transmission goes through the tub. If you hear metal on metal when the washer is spinning, you may need to replace the tub bearing. This bearing is made of metal, and is approximately 3 inches wide and 2 inches tall.
Replacing your General Electric Washer Tub Bearing
Customer Repair Stories
hammering on the tub nut wrench rotated the drive axle & pulley
2nd tip, my washer has the standard agitator with the glued on cap; it was unclear if I needed to remove it; you should clarify that this is not necessary, that one must only pop up the entire agitator; I used a shipping strap ... Read more looped under the agitator and over a 2x4 across the top of the frame, tightening until the tub was raised a bit and then a gentle pop down on the tub and the agitator easily popped off.
-
Martin from LAKE ST LOUIS, MO
-
Difficulty Level:Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
This is a water hose clamp kit for a variety of appliances including dishwashers and washers. This is a genuine replacement part. The kit includes two hose clamps. The smaller of the two is 1 inch in diameter while the larger one is 2 inches in diameter. The hose clamps secure the end of the water hose in place to prevent the hose from leaking. If you notice leaking from the hose of your appliance, you may need to replace this kit. Protect your hands with work gloves during this repair to avoid injury.
The triple water valve or inlet valve in your washer connects to the water source and solenoid wires, and ensures the tub has the right amount of water entering it. If your washing machine continues to fill after it is full, or if it fills slowly, you may need to replace this valve. Before you begin this repair, be sure to disconnect the water and power sources from your washer. This part is sold individually.
Replacing your General Electric Washer Triple Water Valve
Customer Repair Stories
Washer sometimes over-fills with water, may even overflow
-
Robert from FORT MILL, SC
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
Leaking water
-
Paul from LUBBOCK, TX
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
This part is for the hose to outer tub.
This is a water pressure switch hose, also known as the air dome tube, for your washer. It is made of clear plastic and is sold individually. The hose transports water to your water pressure switch, so the switch can control how much water enters the washer during a cycle. If your washer will not fill up with water, or if water continues to fill the tub even after it is full, you may have a damaged water pressure switch hose. Inspect the hose for cracks and leaks, and if the hose is damaged you will need to replace it.
Replacing your General Electric Washer Water Pressure Switch Hose
Customer Repair Stories
Washing machine never stops filling and thus overflows
Disconnected the hose at both ends. Attached the ne ... Read more w hose to the pressure switch and proved it was working by blowing into the hose and getting the water to stop flowing into the washer.
Taped the old hose to the new hose so I could use it as a pull-wire to guide the new hose through its protected housing. Attached the other end of the new hose to the tub and voila, all was well.
-
Paul from BEACHWOOD, OH
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Washer would not stop filling with water
-
Charles from PAINESVILLE, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers
This part holds the water during the wash cycle and houses the spin basket.
Replacing your General Electric Washer Outer Tub
Customer Repair Stories
washer was leaking (noticed during spin cycle)
-
John from Shady Point, OK
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Screw drivers, Socket set, Wrench set
This is a drain pump, designed to work with your washing machine. It expels water from your washing machine during the draining cycle. The most common reason for needing to replace this drain pump is if your unit is not draining properly, is leaking, or if your pumps are not spinning. This model is gray in color and is encased in plastic. It about 9 inches high, almost 6 inches long, and 4 inches thick.
Replacing your General Electric Washer Drain Pump
Customer Repair Stories
Water not completely draining, some left under the drum and in the output hose. Mildew odor.
-
LAUREN from CHARLOTTE, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Wrench (Adjustable)
would not empty the water
-
James from WILLOW STREET, PA
-
Difficulty Level:Very Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Socket set
This part helps prevent the backflow of water from the tub to main water line.