This lower rack wheel kit includes 8 wheels and 8 axles that allow the lower dishwasher rack to slide in and out smoothly. If your dishwasher door will not close, is noisy when operating, or the dishe...
The Rack Slide End Cap is a white one-inch plastic part which replaces the end cap for your dishwasher rack, preventing your rack from sliding too far. If you find the dish rack is causing the door to...
The dishwasher roller assembly attaches to the upper dishrack. It allows the dishrack to slide out easily. If the upper rack keeps falling off the track in dishwasher, the door will not close, the doo...
The lower dishrack wheel on your dishwasher allows the dishrack to roll in and out effectively. If your lower dishrack wheels are damaged, or the rack does not roll in and out, you may need to replace...
This baffle fits the lower right hand corner of some dishwashers. It is black rubber and has a matching left hand lower corner baffle. It is recommended that you replace and install both left and righ...
The corner tub baffle may also be known as the door baffle and is a part used on your dishwasher. The left and right side baffle on your dishwasher should be installed and replaced at the same time. T...
The interlock switch may also be referred to as a belt switch. This part is a simple on/off mechanism that prohibits the appliance from operating when the door is open. This is a part for your dryer. ...
This push on nut is for your dishwasher or refrigerator. As the name suggests, it pushes into place, rather than being screwed in. It is approximately half an inch in diameter and is made of stainless steel.
This part helps keep the rinse aid the dispenser until its needed.
$18.37
In Stock
Questions And Answers for GSD650X-72BA
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jane
December 21, 2022
Serial number DS728736B
How to fix a standing water problem in the dishwasher.
For model number GSD650X-72BA
Hello Jane, thank you for contacting us. First, you need to clean the drain line. Older drain hoses tend to form kinks, which can create blockages. If there are kinks in the drain hose, gently straighten them out. Since an air gap in a connecting hose may prevent water from draining, remove the drain hose where it connects to the garbage disposal and clear blockages with a flat-head screwdriver. After you have removed any clogs, make sure the kitchen sink drain is not clogged and run the disposal. To ensure that your dishwasher is draining properly, turn on the power to the system and run a complete dishwashing cycle. Once the cycle is complete, open the door and check if any water remains in the bottom of the dishwasher. If you still notice an abnormal amount of standing water in the dishwasher, you need to inspect the following parts that can be the culprit and need to be replaced: the drain valve, part number PS259657; the pump and motor kit, part number PS260801; the drain hose, part number PS260686, and the drain solenoid kit, part number PS260462. Please reach out to customer service if you need help placing an order. Glad to be of help!
There are eight guides that hold the rack rails in place. Use a Phillips screwdriver to remove the top two guides on each side in order to remove the rack from the dishwasher. The plastic axles on the rack and the rollers snap on. Use the hammer and punch to bend the metal clip on one end of the rail. Remove the plastic end piece the
... Read moren slide the rollers out. Place two new rollers in the rail and put the plastic end piece on. Use the hammer and punch to bend the metal clip back into place. Snap the rails on the rack and set the rack on the guides in the dishwasher. Replace the top guide using the screwdriver, you will have to twist the rails in order get them in between the guides.
Unsnapped clip,and moved it 90 degrees. Slip wheel and clip off. Installed clip on new wheel. replaced new wheel. The wheel did not come with a new clip and was not suggested on the parts list. The existing clip was still OK but if it was not, I would have had to order a clip and wait. All in all, a good experience.
Open the tiny plastic package in inserted the wheel onto the "axle". Opened the dishwasher, pulled out the bottom rack and snapped the wheel onto the rack. Done!
