Models
>
GMB931HB119
GMB931HB119 General Electric Dishwasher - Overview
Sections of the GMB931HB119
[Viewing 4 of 4]
Keep searches simple, eg. "belt" or "pump".
Silverware Basket (Grey)
PartSelect #: PS261346
Manufacturer #: WD28X265
The silverware basket, used for dishwashers, is in the bottom of the dishrack. The basket is used to hold eating utensils such as spoons, forks, and knives. If the basket is worn out or broken, you sh...
$91.04
In Stock
Piston and Nut Assembly
PartSelect #: PS260690
Manufacturer #: WD24X10018
This is used for the check valve.
$24.34
In Stock
Rinse Aid Fill Cap
PartSelect #: PS2351824
Manufacturer #: WD12X10284
This part helps keep the rinse aid the dispenser until its needed.
$18.37
In Stock
Water Inlet Valve
PartSelect #: PS259411
Manufacturer #: WD15X93
This water inlet valve is specially designed for those dishwashers that fit under the counter from 1974 To Present. The valve should be located behind the lower kickplate panel in either the right or ...
$57.50
In Stock
Adjustable Leveling Screw
PartSelect #: PS1021358
Manufacturer #: WE1M642
The adjustable leveling screws on the bottom of your dryer can be screwed in or out to lower or raise the leg level. If one of the leveling screws is stripped, damaged, or missing, you may not be able...
$16.51
In Stock
Upper Spray Arm Water Supply Hose
PartSelect #: PS260738
Manufacturer #: WD24X214
This is the replacement upper spray arm water supply hose for dishwasher. It is made of white plastic and has a connector piece on each end. This hose supplies water to the upper spray arm, so it can ...
No Longer Available
Third Level Spray Arm
PartSelect #: PS755622
Manufacturer #: WD28X10103
Water is forced through this spray arm by the unit's pump and motor assembly. The force of the water propels the spray arms, spraying water and detergent onto the dishes on the dishrack. This spray ar...
$86.81
In Stock
Drain Hose
PartSelect #: PS260686
Manufacturer #: WD24X10014
This drain hose is an OEM, manufacturer-approved replacement part for your dishwasher. The drain hose filters out the wastewater from the dishwasher. If there is a hole in it, water will leak out of y...
$34.01
In Stock
Hose Clamp Kit
PartSelect #: PS270806
Manufacturer #: WH1X2036
This is a water hose clamp kit for a variety of appliances including dishwashers and washers. This is a genuine replacement part. The kit includes two hose clamps. The smaller of the two is 1 inch in ...
$15.89
In Stock
Screws - 12 per package
PartSelect #: PS312570
Manufacturer #: WZ4X241D
Size - 8-18 ab
$20.05
In Stock
Questions And Answers for GMB931HB119
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the GMB931HB119
[Viewing 6 of 6]Not draining
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Not cleaning dishes properly
Fixed by
these parts
these parts
Show All
Will not fill with water
Fixed by
these parts
these parts
Show All
Will not dispense detergent
Fixed by
these parts
these parts
Show All
Not drying dishes properly
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dishwasher wouldn't fully drain
I removed the four screws holding the screen and molded plastic cage inside the rear of the dishwasher to expose the check valve assembly. I then unscrewed the piston and nut assembly with my hand and replaced it with the new one. I found that the rubber cone shaped valve on the old piston and nut assembly was entirely disintegrated. T
... Read more
his easy repair solved the problem.
Read less
Parts Used:
-
Dan from Minnetonka, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
189 of 204 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Insufficient fill water, dishes not getting clean (valve diaphram had ruptured)
1. Remove lower cover skirt.
2. Shut of water at undersink valve.
3. Unplug power cord or turn off circuit breaker.
4. Disconnect water supply line from fill valve.
5. Unplug the electrical connector from the valve.
6. Remove the 2 valve mounting bracket screws.
7. With loose valve in hand, rotate to g ... Read more ain access to allow release of outlet hose clamp for hose removal.
8. Remove brass fitting from old valve and install on new valve. Use teflon tape on the pipe threads only.
Install new valve by reversing the procedure.
2. Shut of water at undersink valve.
3. Unplug power cord or turn off circuit breaker.
4. Disconnect water supply line from fill valve.
5. Unplug the electrical connector from the valve.
6. Remove the 2 valve mounting bracket screws.
7. With loose valve in hand, rotate to g ... Read more ain access to allow release of outlet hose clamp for hose removal.
8. Remove brass fitting from old valve and install on new valve. Use teflon tape on the pipe threads only.
Install new valve by reversing the procedure.
Read less
Parts Used:
-
Don from Mount Vernon, IL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Wrench set
71 of 77 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Basket was lost
Opened package from Parts Select.
Removed Silverware basket from package.
Opened Dishwasher.
Inserted Silverware Basket in rack.
Closed Dishwasher.
Discarded shipping package.
Told wife I fixed Dishwasher.
Sat down & had a beer.
Removed Silverware basket from package.
Opened Dishwasher.
Inserted Silverware Basket in rack.
Closed Dishwasher.
Discarded shipping package.
Told wife I fixed Dishwasher.
Sat down & had a beer.
Parts Used:
-
Joseph from Elmendorf, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
49 of 52 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!