This sensor (Temperature Sensor, Thermistor, Refrigerator Temperature Sensor) sends the temperature reading of the compartment to the control board. If you notice your refrigerator is too warm, too co...
$27.00
In Stock
Order within the next 12 hrs and your part ships today!
This NSF-certified water filter helps to improve the taste, quality, and health of your water by removing a number of contaminants including mercury, lead, and trace pharmaceuticals. The filter should...
$92.40
In Stock
Order within the next 12 hrs and your part ships today!
The interior light of your refrigerator is controlled by a switch that is activated when the door is opened and closed. If your refrigerator light will not turn on, there could be an issue with the sw...
$8.56
In Stock
Order within the next 12 hrs and your part ships today!
This door shelf bin is an authentic OEM part sourced directly from the manufacturer. It is designed for use in your GE refrigerator. It is made of white and clear plastic, and houses items on your ref...
$68.24
In Stock
Order within the next 12 hrs and your part ships today!
This is a door handle fastener to secure the handle to your refrigerator drawer. It is also known and a mounting bolt or screw. It is approximately 1 inch in total length, and is made of metal.
$13.13
In Stock
Order within the next 12 hrs and your part ships today!
This OEM part is from GE and is designed for use in your refrigerator. This part is known as a door mounting screw, and is for mounting the handles of the refrigerator to the door studs.
$13.78
In Stock
Order within the next 12 hrs and your part ships today!
The evaporator fan motor circulates air through the fresh food compartment for efficient cooling.
$51.41
In Stock
Order within the next 12 hrs and your part ships today!
Questions And Answers for GFE27GGDCWW
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Rick
November 15, 2023
Getting water under the full width temperature controlled drawer. After a day there's about a cup. Given some time it will freeze.
This fridge came with the house I bought and noticed about an inch of ice at first. After a while there's water on the floor, looks like it may be defrosting causing the water to run down the right side onto the floor.
Anyway I can't seem to determine where or how it's getting there
Got a part from ya'll not too long ago which fixed my water dispenser
Any ideas regarding the water under the drawer?
Thank you kindly,
For model number GFE27GGDCWW
Hello Rick, thank you for getting in touch. Based on our understanding of the issue, it seems that there is an issue with the drain tube. It comes with the valve. The drain tube and valve for your model is part number PS12344758. It carries water formed during the defrost cycle to the drain pan at the bottom of the refrigerator. We hope this solves your problem!
Replaced both temp sensors(frig comp/freezer comp) frig is still not cooling. What could be the problem?
For model number GFE27GGDCWW
Hello, Thank you for your question. When you are having temperature problems in your fridge, there are a few parts that could cause the issue. You can use a multi meter to test most of the parts. Make sure you cut power to your appliance before doing any repairs or tests. First you should test your defrost thermostat. Place the thermostat in ice cold water for 2-3 minutes after removing it from your appliance. It should be reading 0 ohms to be working correctly. Another part to check would be your defrost heater. Remove it from the appliance. It should be reading anywhere between 0 - 50 ohms to be working. You could check your temperature sensor. To find the correct reading for this part you will have to refer to your tech sheet that comes with your appliance. You can usually find this tech sheet behind the bottom grille of your fridge on either the right or left side. These are the most common parts that cause this issue in your appliance. So it is suggested you check them first. I hope that helps. Good luck with your repair.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
I went to a GE repair center to explain my problem, the service center reccomended that I have a techinician come out o look at it. $75.00 for the visit and what ever labor and materials wuld cost.
I went on line to see if there were others having this same problem and found that there were many with the same problem.
... Read more />After reading some of the ways that people found out what was wrong ...it became a matter of three components, the timer, heater or thermostat.
I tried the most common component and the less expensive one first , the thermostat switch I installed it very easily snipping two wires and attaching the news using wire nuts I used the diagram on this website to pinpoint the component and there has not been a problem since.
I applied some tips learned by reading other reviews. So before I started I grabbed my trusty vise grip pliers and a small screw driver. I locked onto the switch actuator, the part that the refrigerator door pushes in, with the vise grips and pulled on it just hard enough to get the screw driver inserted in the right side to push in the c
... Read moreatch clip so the switch could be pulled out further each time the catch clip was depressed to the next detent. Then I used the screw driver on the left site to encourage the switch past the detents on the left and very quickly the switch was out of the mount. The wires from the refrigerator pulled out with the old switch. I unplugged the old switch from the wires and plugged in the new switch and shoved the new switch back into the mount, wiggled it a couple of times to make sure it was secure and the job was done. Once I applied the vise gripes at first, the whole job took less than a minute.