FDB2410HIC0 Frigidaire Dishwasher - Instructions

Disconnect from power
Unscrewed 4 phillips screws from top of outer door.
Unscrewed 2 screws each siide of door.
Lower outer door section drops away.
Note wiring sequence on dispenser, then disconnect wires.
Unscrew 6 screws on dispenser and lift dispenser out.

Place new dispenser in place (note orientation), ann fasten in place with screws, remembering to replace wire retainer on left lower screw.
Reconnect wires to dispenser correctly.
Slide lower outer door over tabs and secure with the 4 side screws.
Ensure lower door is up under control panel and secure with the 4 top screws.

Fill dispenser with detergent, reconnect power and test run while enjoying a cup of tea in celebration of a job well done..

removed front face of dishwasher removed 2 screws holding latch and removed 2 push in plugs reinstalled the same.
job completed in less than 15 min.

The only difficultpart was to figure out how to remove the stainless cover from the door. Seems it slides upwards after screws are removed. After that it is self explainatory and goes back together in 5 minutes.

After turning of the power to dishwasher, I opened the door took of the two bottom screws on both sides of door. Closed the door and front panel just slide off. Then I took a picture of the dispenser to make use I could figure out how to put the wiring back together. Removed the six screws holding it in place and popped the dispenser out. Easy .. popped new dispenser in and lightly put all six screws back in ,wired it back up after checking my photo. Closed the door ,slid front panel back on opened the door put the 4 screws back in that hold the front panel .Turned power back on and Boom!! All done.. Not bad for a girl...

removed the screws holding the door together, then removed the screws holding the dispenser to the interior door. replaced the wires and put the door back together

Remove front Fascia on floor, use AC sniffer find hot wires into unit. Flip circuit breaker at panel. Verify no AC, shut water valve off on Dishwasher supply. Disconnect two valve wires to solenoid. Use wrench set to find proper size and use to remove supply line. Unscrew two Phillips sheet metal screws that hold valve support bracket and remove bracket with it now being held in by water inlet valve hose to interior wall of Dishwasher. Use Tin Snips to cut off metal band securing hose to old water inlet valve. Place new valve onto inlet hose, secure with new hose clamp (you must supply) tighten hex nut on clamp till water tight. Fasten wires onto the solenoid and mount assembly support bracket to dishwasher. Now connect water supply line after wrapping threads with pipe dope tape fasten and secure nut with adjustable wrench till water tight open supply valve and look for leaks with a flash light. If no leaks, reset breaker and test run and drain. No leaks replace fascia and have a Beer great Job saved $850 min. on a new dishwasher!

The video show a different model, the only difference is that the screws for the top part shouldn't be removed only the ones that hold the front. Replace the detergent dispenser once the cover is removed is easy. All works like brand new. Thanks.

Needed to replace detergent / rinse aid dispenser unit on the inside top of door.

1) Need to remove outer door cover / panel by removing just two (2) screws - bottom screws on lower side panel. Door panel will drop vertically 1" to remove it.

2) Mark and disconnect the four (4) wires connected to the dispenser unit. The connections were so tight, it required pliers and a screw driver to loosen them.

3) Dispenser unit has four (4) screws holding it in place. Unscrew them and remove unit through door interior - this requires a bit of angling to get it out.

4) Position new unit through interior. Screw in place.

5) Re-attach four (4) wires in same sequence as disconnected.

6) Re-attach outer door cover. This is the most difficult part and really requires two people. It consistents of two sets of guide channels that most be aligned for the door panel to be secured re-attached.. Once aligned, the door cover must be moved vertically about an 1" and the screws re-attached.

Turned power supply off to dishwasher Opened door and removed screws holding font of door Unplugged soap dispenser and removed six screws. Popped out and installed new dispenser. Plugged wires into new dispenser and installed front of door. Easy

replaca latch as you mentioned

Although some on-line "how to's" suggested replacing it while it while it was still hooked up, it was far easier to disconnect the electrical wiring, water supply and waste hose, then to pull it out from the wall and place it on its back. The pump would be nearly impossible to change by leavng everything hooked up and attempting to replace it from underneath. Do buy new clamps as the old ones are virtually unusable from the factory. Do also have a few old rags around to soak up the waste water.

Removed 4 screws on door cover, 6 screws on dispenser 4 wires and reinstalled new one. Done less than 20 minutes.

This was a quick job once I had the part. I removed the door panel and control panel. Replaced the latch and put everything back together. Simple!