Quick Question!

Have you ever purchased from PartSelect.com before?

Models > FDB1502RGS4

FDB1502RGS4 Frigidaire Dishwasher - Overview

Get Parts and Repair Help for FDB1502RGS4

If you know the dishwasher repair part you need, you can browse the list of all parts on the FDB1502RGS4, or you can search by name or part description. You can also find your part by where it is located on the FDB1502RGS4 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for FDB1502RGS4 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$10.15

Bottom Door Gasket

This gasket is found at the bottom of the dishwasher door and helps prevent water from leaking from the bottom edge of the dishwasher door. If your dishwasher is leaking water from...

$15.36

Tub Gasket - Gray

This dishwasher door gasket creates a seal around the dishwasher to ensure that water is not able to leak out. If this was not in place there would be a gap between the opening of the dishwasher tub and the outside of the door. If this has torn, you might notice leaking water coming from your dishwasher or the inability to shut the door properly. Simply pull out the current gasket, ensure the area is clean, look for the indicator on your new gasket to determine the middle, and press into place without stretching the material. After the repair is complete, shut the dishwasher door and leave closed a few hours to ensure it properly seals into place.

$18.41

SPRAY ARM

Helps distribute water from the top of the dishwasher tub.

$55.63

Lower Dishrack Assembly

This white lower dishrack assembly comes with eight light-gray rollers for easy access. The dishrack is approximately 21 inches wide x 22 inches deep. The dishrack holds dishes in place during the dishwashing cycle. If you see rust spots on the dishes, the lower rack will not pull out, or the lower rack is visibly rusted or damaged, you will need to replace the part. Other common symptoms include: unusual or loud noises coming from the unit, or the dishes on the lower rack not being washed properly. This part is also known as a dish rack or a dishwasher rack.

$26.85

Water Inlet Valve - 120V 60Hz

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner of the dishwasher. The attaching solenoids on the valve open and close ...

$43.53

Upper Dishrack with Wheels

The upper dishrack, a vital part in a dishwasher, holds the dishes in place as the dishwasher goes through its cycle. If the wheels are missing/broken, the upper rack is damaged, or it starts to rust, replacing and installing a new dishrack could solve this problem. Customers rate this installation process as easy and no tools are required. Make sure to remove any items on the top rack before unhooking the tab of the rack stop on both ends and pulling it from the rail. Next step is to remove the upper spray nozzle and replace it with new one. Refer to the manual instructions for further guidance.

$6.03

Single Rack Roller Kit

The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not c...

$29.77

Lower Spray Arm with Shields

This lower wash arm is located in the bottom of the dishwasher. The spray arm of this part rotates to spray water inside the dishwasher tub to clean dishes. If your dishes are not getting cleaned properly or your dishwasher is making unusual noises and leaking water, replacing this part can fix the problem. To repair, first open the dishwasher door and pull out the lower rack. Next, remove the lower wash arm by flex out tabs to release it. Now you can replace new lower wash arm by lining it up and pushing down to lock it in place. Pro tip: make sure to spin it around a bit to make sure it works. Refer to the manual provided by the manufacturer for further installation instructions. Make sure to unplug your appliance from the power source before beginning this installation.

$3.73

Heating Element Brass Nut

The heating element nut is used to connect the heating element to the dishwasher tub. If water is leaking from underneath your dishwasher, you may need to tighten or replace the he...

$17.40

BASKET

The silverware basket, used for dishwashers, is in the bottom dishrack. The lower dishrack basket is used to hold eating utensils such as spoons, forks, and knives, and other small tools. If the basket in the dishwasher is worn out or the basket is broken, replacing it can be a solution. No tools for this replacement are required, as it is an easy process. If you need further guidance refer to the instructions provided by the manufacturer. For safety precautions make sure to unplug the dishwasher and wear gloves.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The spray arm would fall off during the washing cycle.

  • Customer: Roy from Worcester, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 726 of 733 people found this instruction helpful
Repair was simple. I unscrewed the old grommet which held the old spray arm and screwed-on the new one. About 30 seconds was required. Other people having this problem should note that the spray-arm is made of three pieces which are inseparable when the arm is new. The arm is sold in this form. However, when your machine is having the problem that the a... read more

Water leaking from Inlet Valve

  • Customer: CHRIS from ROANOKE, VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 574 of 585 people found this instruction helpful
Remove the bottom cover plate. Disconnect the water inlet and black rubber hose. Remove 2 mounting screws. Pull out electrical connector. Reverse order. Be sure to get the brass inlet connector really tight so it won't leak. I did the final tightning after the part is mounted. Not a bad repair at all. The only problem was that it leaked in the first ... read more

Lower Rack Roller Missing

  • Customer: Sandra from Mount Vernon, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 365 of 367 people found this instruction helpful
Took the roller out of the package, snapped it into place. Less than 15 seconds. Works good as new. read more