Models
>
ELFG7437AW0
ELFG7437AW0 Frigidaire Dryer - Overview
Sections of the ELFG7437AW0
[Viewing 5 of 5]
Keep searches simple, eg. "belt" or "pump".
M Series Ignition Coil Kit
PartSelect #: PS470049
Manufacturer #: 5303931775
This kit contains two coils, one is a two-wire secondary coil and the other is a three-wire booster coil. Both coils in the ignition coil kit should be used together in the clothes dryer. Some of the ...
$21.45
In Stock
Screw
PartSelect #: PS417463
Manufacturer #: 131302800
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
$11.21
In Stock
Flame Sensor
PartSelect #: PS459818
Manufacturer #: 5303281135
This part senses the flame for heat allowing the gas valve to open. The most common issue that might arise that would indicate the flame sensor needs to be replaced is your dryer is not giving off eno...
$28.57
In Stock
High Temperature Adhesive
PartSelect #: PS474458
Manufacturer #: 5308027429
This high temperature adhesive is used for installing felt and rubber seals on dryers. The tube contains 1 ounce of product. This adhesive is made to withstand extremely hot temperatures. Before apply...
$47.69
In Stock
Belt
PartSelect #: PS2349294
Manufacturer #: 134719300
This dryer belt is one of the most important parts in a dryer and is what allows the dryer drum to spin/rotate. If the dryer belt is damaged or broken, the drum will not spin or will have difficulty i...
$57.93
In Stock
FILTER ASSEMBLY
PartSelect #: PS16620745
Manufacturer #: 5304529766
Lint filter assembly. Part has been redesigned. If you are replacing this filter you may also need to replace grille as well. Please see model diagram for correct grille.
$85.66
In Stock
MOTOR
PartSelect #: PS16620747
Manufacturer #: 5304529782
This drive motor includes the pulley for the dryer drum belt. The motor has reverse threads for the blower wheel. Please disconnect the power before starting your repair. This is a genuine OEM part.
$193.95
In Stock
Questions And Answers for ELFG7437AW0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the ELFG7437AW0
[Viewing 4 of 4]Noisy
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Not Heating
Fixed by
these parts
these parts
Show All
Drum Not Spinning
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer would heat initially then cool down
The top of the dryer was easily removed by prying the front up with a screwdriver then tipping it back and off of the mounting brackets. Then the front of the dryer was removed by unscrewing a single screw on each side that held the front to the side panels then pulling the front away from the dryer. Once the front was off, the coils we
... Read more
re easily accessible on the bottom left side. A metal bracket held the coils on and was somewhat tough to get the two screws removed on it as they were stuck, but once they were removed the coils easily came out and I was able to replace them in minutes. The whole job took 15-20 minutes and I now have a dryer that heats through the entire drying cycle.
Read less
Parts Used:
-
Brett from Monticello, MN
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
96 of 109 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer would heat only on the initial start. Burner would not light again until completely cooled down. The ignitor would energize, but no gas would flow for ignition.
1. Pry Dryer top up and off the clips. (Front of Dryer)
2. Remove 2 phillips screws on the inside of front panel.
3. Lift front panel up and set off to the side
4. Removed 2 phillips screws with short handled phillips driver that hold the gas valve coil bracket in place.
5. Unplugged and removed both coils, install ... Read more ed new coils and bracket. Re installed front panel, screws and top.
2. Remove 2 phillips screws on the inside of front panel.
3. Lift front panel up and set off to the side
4. Removed 2 phillips screws with short handled phillips driver that hold the gas valve coil bracket in place.
5. Unplugged and removed both coils, install ... Read more ed new coils and bracket. Re installed front panel, screws and top.
Read less
Parts Used:
-
Bruce from Burnsville, MN
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
40 of 47 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No heat, but everything else works. Ran continuity tests on everything and found gas valve solenoid coils open.
Just as others described in your forum, getting to the gas valve solenoid coils is relatively easy. Pop the top lid and lay it back, remove 2 inside screws that fasten the front cover and pull back off the snap clips and lift up and off. Remove 3 screws that hold the entire gas control assembly to the bottom of the dryer and remove. U
... Read more
nfasten 2 screws on the valve that lock the plate on top of the two coils, unplug the electrical spade lug connections and remove. Install the new coils and do everything in reverse. Easy as 1-2-3.
Read less
Parts Used:
-
Barry from Fremont, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench set
27 of 31 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!