Enter the code TAKE10OFF at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on May 28 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Door gasket broken up
It took considerable time to remove the door and take it completely apart so the gasket could be inserted, and time again to reassemble properly. The gasket (though the no. was confirmed before ordering) was 3" too short so I had to cut some off the old gasket to make do (not entirely effectively).
Very simple repair. I bought the Range without the Burners and Burner Caps. So all I had to do was to purchase the Burners and the Burner Caps and drop them in. Wish everything in life would be that simple.
Removed the two screws put the heat shield off the old one onto the new one put new bottom in and tightened two screws. Done #38. 69 Cost of part with shipping cost included.
Pull plug and shut off gas! The lower oven burner is held in with two rear and one front screws. I removed the top floor of the oven (two hand tightened screws at the back), the bottom drawer, and the front door (just lift it off the hinges). This allowed me to access the burner, and I removed it by unscrewing the three screws, unhitching the igniter connector, and lifting the burner and igniter up and out. I connected the new igniter on the new burner before installing it in the oven, and found that the connector did not match (I was warned about this possibility on the PartSelect site), but instead of splicing the wires together, I cut off the connector on the new igniter and replaced it with the connector of the old igniter. Then I screwed the burner into the oven, recoupled the connector, replaced the floor, drawer, and door, and I was done! It took about 45 minutes.
First I removed the oven door handle from the inside by removing the 2 screws. The screws have standard hex heads. You need to be careful you don't strip them. Once you remove the 2 screws for the handle the outside frame for the door will come away from the oven. You then need to remove the frame by unscrewing 2 screws at both the bottom left and bottom right corners of the door. Once you remove these, the exterior door frame will come away from the oven. The replacement glass actually sits on the outside of the frame. You simple need to slide it up into the top edge of frame. There are little grooves that hold it at the top. Once you have it in place, slide the bottom edge of the glass into the grooves on the bottom of the front door. Replace the 2 screws at the bottom right and left corner and then tighten the screws for the handle on the inside of the oven door and you're done. Pretty simple really.
Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.
Twice I ordered the oven light bulb & each time the light bulb was defected
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.
This was not really a repair. Just replacement. The burner caps get discolored rather quickly and nothing removed the stains. I'm thrilled to have replacements on hand.
Removed the old caps, replaced them with the new ones.
the flame spreader through the years, developed a hole above the glow coil causing the above trapped gas between the oven pan and spreader to ignite. by replacing the flame spreader the problem is gone and is now working properly. thank you, parts select for being there when i needed the part and also being reasonably priced. mike marino
Was able to see the exact part with easy to read schematic so I knew I was ordering the right part. Then just switched out the old for the new. Looks like a new cooktop except for the scratches in the stainless, but we are working on that! Thanks!