EF36IWFSS Dacor Refrigerator - Instructions

I removed the ice maker assembly from the freezer compartment (four nuts/ nut driver) and unplugged the wire harness. I discovered the nature of the problem and I went on the Internet to look for replacement parts expecting I'd have to buy the entire ice maker. When I found PartSelect.com I looked through the pictures of the parts available for my ice maker. I found the correct part quickly and easily. And having an acurate photo on the site, I was able to match all the key features of the mold I had with the one on the screen. I ordered the part, and installed it the day it arrived with just a Phillips screwdriver and a nut driver. It functions perfectly.

Turned old one until it snapped out. Replaced it with a turn.

Pushed the hinge pins aside and removed the old lid.. Reversed the process to install the new lid

First I removed the drawers above the pantry drawer. Then I took out the pantry drawer. I unsrewed 3 screws that attached the part to the refreg. I then removed the rails that were attached to the part I was repalcing and put them on the new part. I then install the new part. Put the firg back together. It was extremely easy and took about 5 minutes to do.

First I removed the icemaker from the freezer by removing two horizontal screws holding it to the side wall, and one vertical screw holding the front to a bracket coming off the side wall. Then I used a flat screwdriver to unlock the electrical plug. (After doing this, I realized that this wasn't necessary at all, and this part could have been changed just as easily without removing the icemaker.) On the front, there is a white cover with Ice Maker Plus. Use a flat screwdriver to unlock the tangs and remove the cover. There are three screws in the corners that once removed, will allow the motor assy. to be gently pulled straight out. On the back of the part, you will see many gold lands that the timer touches. I don't think there was anything wrong with my motor. I had two spots where the gold plating was worn off, so I suspect it was not making contact, and the whole process would stop. Slide the new part in place making sure the teeth on the gears line up (not a big deal), and secure with the screws. Install cover and you're done. Mine has been making ice like it was brand new.

Removed the metal cover over the HV electronic board on the back of the unit. Using a flat head screwdriver I unsnapped the plastic cover and removed it. I unplugged the 5 or 6 cables from the electronic board. Bent back the plastic tabs holding the board. You might think they are going to break but they bend. I lifted the board out and replaced it with the new one. Then plugged the cables in being careful to align them first. I then applied power and the refrigerator came to life. I followed the programming instructions that came with the refrigerator. You can get those online also. The unit began to run and in a few minutes the compressor came on. The unit began cooling and life was good again!

I unboxed the replacement gasket set and inspected them for damage. Then I opened the left refrigerator door and grabbed the right hand corner of the old gasket and removed it. I then aligned the new gasket with the door and using my fingers pushed the gasket into the gasket grove. I used my thumb to seat the gasket. I repeated the process for the right door. Total time was under 15 minutes.

Since the crisper didn't come with a front, the old front needed to be removed from the broken cripser and attached to the new one. The easiest way to take off the front is to remove it from the bottom of the crisper. Once the pressure is released it comes off easy. Snap the front on the new crisper by starting with the top and snapping the bottom.

changed the starter connected to the compressor

Turned the old one to unseat and replaced with a new one in the reverse order.

Simply move the appliance for access to the back side. Removed the lower metal access panel, locate the compressor ( black round object ) parts are on the left bottom of the compressor. Simply unplug the parts, and replace with new parts.The hard part was, getting my 72 year old body in position to do the job. As far as getting the right part, a young lady in Nova Scoita is the one to ask for help !! Ordered parts one day, and they were in my hands the next morning!!

Repair was easy and producing ice within five hours.

This is the 2nd part I have bought for this refrigerator from Part Select. I wish the parts came with some kind of instruction. I had to re-use parts from the original equipment each time. After studying the replacement part I was able to figure out what I needed to do, but it would have been nice to have a little more information. There were 3 pieces which I needed to remove from the damaged piece and add to the replacement part. I would gladly pay more for a complete replacement part.

I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened the screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!

Replaced with new gasket