The drum belt attaches to the motor pulley and causes the drum to spin as the motor is rotating. The drum belt is made of black rubber. This is an easy repair and should only take a few minutes. This ...
This is a thermistor, also known as a dryer thermistor. The thermistor is attached to the blower housing, it will help regulate and oversee the temperature within the dryer. The most common symptom of...
This idler pulley assembly is sourced from the original manufacturer for use in dryers. The assembly includes the pulley wheel and bracket. It is found near the motor where it provides tension to the ...
The drum support roller and axle, which includes the roller shaft and mounting clips, is used in dryers. This part holds the drum as it rotates on the support wheels. When the roller begins to wear ou...
This thermostat is a genuine OEM part and is manufacturer-approved for electric dryers. The thermostat is responsible for monitoring and maintaining the temperature inside the dryer during the drying ...
The thermal fuse measures the air temperature inside your dryer drum, and turns the heat on and off to maintain the optimal temperature during the drying cycle. If your dryer will not start, dry cloth...
This moisture sensor plate is specifically designed to fit with your Samsung dryer. It is made of stainless steel and measures approximately 5 inches long. It is designed to detect the amount of moist...
The high limit thermostat is designed for use in your dryer. The function of this part is to make sure that your dryer does not get too hot. If your dryer is not regulating heat properly, you may need...
This lint screen case, or lint filter case is specially designed for Samsung dryers. It is responsible for securing the lint screen inside the lint screen housing and preventing it from falling out. T...
This thermal cut-off fuse bracket assembly is a genuine replacement part supplied directly by Samsung for use in dryers. It is a safety component that is designed to protect the dryer from overheating...
Leveling leg supports the dryer. Adjust the height of the leveling leg to make the dryer level.
$21.16
In Stock
Questions And Answers for DV50K8600EV
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Michael
March 30, 2023
My dryer has begun making a squeaky noise when I first turn it on that lasts for about 20-30 seconds. It began a while ago with intermittent noise but now it has become pretty consistent. Is it likely to be the idler pulley, drum support roller, drive belt or should all be replaced? How do I confirm that is the issue before I just start buying parts that may not be needed.
For model number DV50K8600EV
Hi Michael, thank you for getting in touch. According to our research, first, you may need to check the drive belt, part number PS4133825, for any wear and tear. Over time, the drive belt can dry out or burn out and start to crack. Eventually, a piece of the belt can break off, causing the belt to make a loud noise whenever the motor is running. If the drive belt is not damaged, you may need to check the idler pulley, part number PS11771601. The idler pulley might be worn out, cracked, loose, or bent. Remove the idler pulley and inspect it carefully. If the idler pulley is not faulty, then you may need to check the drum rollers, part number PS4221885, which might be worn out. We hope this solves your problem!
This dryer drum will not start rotating until it is pushed a little while holding in the door closed switch. After it starts spinning everything is fine. Is there a start capacitor on the motor that turns the drum that might be bad?
Thanks.
For model number DV50K8600EV
Hello Raymond, thank you for contacting us. Based on the description that you have provided, we would recommend checking the motor capacitor to fix the issue. The capacitor does not come separately and comes as a part of the drive motor, part number PS4204647. Glad to be of assistance!
YouTube, YouTube, YouTube. I YouTubed many videos on how to take a dryer apart to reach the drum support roller and axle. After watching numerous videos, I settled on one that had my exact model of dryer. For my dryer, previous inputs said I needed two rollers to for my model. That is not the case. My model actually has 4 rollers, 2 in th
... Read moree front and two in the back. I ordered 2 initially but only needed 1 thankfully since only one roller was bad. Keep it simple stupid is how I got it done. Dryer's are pretty simple machines mechanically. Don't trash your noisy dryer. We bought ours in 2014 and it only recently started giving us issues. This is after 2 moves and being run daily for a family of 6. I'm glad I found partselect.com. They saved me a ton of money.
Watched a video on utube, how to repair my 16 month old steam dryer. The hardest part was laying on my belly holding the spring loaded tensioner and slipping the belt on around the blower housing. Only cost me $23. Winning!
