Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DLE3733D

DLE3733D LG Dryer - Overview

Get Parts and Repair Help for DLE3733D

If you know the dryer repair part you need, you can browse the list of all parts on the DLE3733D, or you can search by name or part description. You can also find your part by where it is located on the DLE3733D by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$32.77

Drum Support Roller

This part is sold individually. The drum support roller is found in your dryer. It is used to hold the drum in place in the cabinet while letting the drum rotate on the support rol...

$30.05

Lint Filter

The lint filter in your dryer is used to collect lint as it passes through the dryer vent. If you notice that your dryer is not providing enough heat, or if it takes too long to dry, you may need to replace the lint filter. You should also replace the lint filter if you notice it is damaged during regular maintenance. Many of our customers have rated this repair as easy. To complete the repair, simply remove the old lint filter and replace it with the new one. You may want to use a flat head screwdriver to remove any residual lint before you install the new filter.

$5.72

Sensor

The sensor controls the temperature in your dryer and will turn off once your clothes have reached the desired dryness level. If you notice that your dryer is not giving off enough...

$15.54

Thermal Fuse

This thermal fuse acts as a high-limit thermostat, and shuts off the heating element when the dryer overheats by cutting off power to the dryer. If the thermal fuse has blown, the dryer will not start. These fuses cannot be reset, so if yours has blown, you will need to replace it. A common reason for the thermal fuse to blow on a dryer is if the exhaust vent on your dryer is restricted or blocked. Hot air will be confined in the dryer and the fuse will trip and stop the electricity from flowing to the gas valve or heating element.

$15.54

THERMOSTAT

The thermostat is a part for your dryer, and it is roughly 1 inch long by roughly 1.5 inches wide. The purpose of the thermostat is to measure the temperature of the air inside you...

$17.98

Thermistor,NTC

This dryer thermistor temperature sensor helps monitor and regulate the temperature inside a dryer. This part includes the wire harness. If your dryer overheats, does not produce enough heat, or takes too long to dry, then the thermistor might be defective or damaged. This can cause a fault code and could begin either prolonging or shortening drying time. As a safety precaution, make sure to unplug the dryer from the power source before beginning this installation, and wear gloves to protect your hands. Refer to the installation instructions provided by the manufacturer for further guidance.

$26.70

BELT,POLY V

This dryer belt helps rotate from the drive motor to the drum. It is located between the motor and the tub. If you notice that your dryer is noisy or is not tumbling this could be ...

$21.53

Cover,Guide

Located just inside the dryer door. The guide cover (or grill cover) is where the hot air circulates through the appliance. This part may crack or become damaged over time, causing clothes to get caught on it while it is in motion. Open the dryer door, remove the lint screen, and remove the screen using your screwdriver. Line up the new grill cover with the moisture sensor and the housing on either side, and it should snap into place. Once it is firmly in place, use your screwdriver to put the screws back in.

$143.18

Heating Element Assembly

They are all strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current and as a result, the wire heats up. The h...

$14.73

ROLLER ONLY

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broke the tub drum

  • Customer: Sergio from CORNELIUS, OR
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 4 people found this instruction helpful
Exchange read more

Light bulb in dryer burndt

  • Customer: Duane from TROY, TX
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Removed cover replaced bulb read more

dryer wouldn't heat

  • Customer: Bryan from Spokane, WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the heating element, tested it, purchased a new element and installed. read more