Models > DDG8205NC

DDG8205NC General Electric Dryer - Overview

Sections of the DDG8205NC

[Viewing 1 of 1]
Diagram and Parts List for General Electric Dryer
Keep searches simple, eg. "belt" or "pump".
Rear Drum Bearing – Part Number: WE3X75
Rear Drum Bearing
★★★★★
★★★★★
(2)
PartSelect #: PS267865
Manufacturer #: WE3X75
This part is the rear dryer drum bearing only. This part helps keep your dryer running smoothly as possible with as little noise as possible.
$18.73
  In Stock
Gas Igniter – Part Number: WE4X444
Gas Igniter
★★★★★
★★★★★
(4)
PartSelect #: PS268028
Manufacturer #: WE4X444
Be very careful to not handle the igniter by its gray part. Hold it by its white tip only.
$49.76
  In Stock
Drive Motor – Part Number: WE17X10010
Drive Motor
PartSelect #: PS1559768
Manufacturer #: WE17X10010
Replaces "T" and "V" style motors. Includes two motor pulleys. If you have an older model dryer, the pulley may be pressed on or held on with a set screw. If pulley is pressed on, a new motor pulley must be ordered.
$349.53
  In Stock
Door Switch – Part Number: WE4X197
Door Switch
PartSelect #: PS268004
Manufacturer #: WE4X197
This part has three terminals. Note: Use the two smaller terminals for models that only have two wires to the switch.
  No Longer Available
Blower Wheel – Part Number: WE16M15
Blower Wheel
★★★★★
★★★★★
(1)
PartSelect #: PS960003
Manufacturer #: WE16M15
This wheel attaches to the motor.
$74.30
  In Stock
Timer Knob – Part Number: WE1X1266
Timer Knob
PartSelect #: PS266957
Manufacturer #: WE1X1266
This knob accepts a D-shaped shaft.
  No Longer Available
Multi Rib Belt - 4 Ridges – Part Number: WE12X49P
Multi Rib Belt - 4 Ridges
★★★★★
★★★★★
(1)
PartSelect #: PS265703
Manufacturer #: WE12X49P
This dryer drum belt goes around the dryer drum and the pulleys to rotate the drum once motor is activate.
  No Longer Available
'K' Series Coils
PartSelect #: PS268074
Manufacturer #: WE4X560
This 'K' series three-coil coil kit fits older model GE clothes dryers. It comes with the wiring harness and the igniter bracket.
  No Longer Available
SLIDE Assembly – Part Number: WE13X93
SLIDE Assembly
PartSelect #: PS265897
Manufacturer #: WE13X93
$41.27
  Special Order
DISCONTINUED – Part Number: WE12X45
DISCONTINUED
PartSelect #: PS265699
Manufacturer #: WE12X45
  No Longer Available
THERMOSTAT – Part Number: WE4X325
THERMOSTAT
PartSelect #: PS268018
Manufacturer #: WE4X325
$28.01
  Special Order
LINT FILTER – Part Number: WE18X34
LINT FILTER
PartSelect #: PS266258
Manufacturer #: WE18X34
  No Longer Available
View More
Back to Top

Questions And Answers for DDG8205NC

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Back to Top

Common Symptoms of the DDG8205NC

[Viewing 1 of 1]
Noisy
Fixed by
these parts
Fixing Fixing Fixing
Show All
Back to Top
Replacing the Blower Wheel

Replacing the Blower Wheel

View More
Back to Top
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Gas dryer heat would not come on
Unplugged dryer, opened lower panel. Loosened the bolt that holds igniter assembly to gas unit and removed old igniter. Put new igniter in the pinch clamp then (being VERY careful so as not to crack new part) replaced igniter assembly and tightened its bolt firmly. Voilà, ignition!
Parts Used:
Gas Igniter
  • Jeff from Seattle, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Wrench set
40 of 58 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replqce bad switch
pried old switch assembly from front of machine with screw driver. removed 2 electrical connections. shorted terminals to verify problem. inserted wiring terminals to new switch. verified operation and then pushed switch assembly into machine opening.
Parts Used:
Door Switch
  • Robert from Virginia Beach, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
30 of 33 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old drum bearingwore out, squeeking like a banchee
Received part in two days.
Removed inspection plate by removing two screws. .Drum bearing was right there. With screwdriver
removed "c" clip, took out what was left of old bearing.
With screwdriver aligned drum, slide new bearing into place. Job was done. Instruction with new part simple and easy to follow.
Parts Used:
Rear Drum Bearing
  • JOE from Galion, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
17 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
View More
Back to Top