Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DBB3300GA2AA

DBB3300GA2AA General Electric Dryer - Overview

Get Parts and Repair Help for DBB3300GA2AA

If you know the dryer repair part you need, you can browse the list of all parts on the DBB3300GA2AA, or you can search by name or part description. You can also find your part by where it is located on the DBB3300GA2AA by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for DBB3300GA2AA parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$6.90

Drum Bearing Slide - White

This is a drum bearing slide, also known as bearing drum slide, glide, or pad, that is fitted to a dryer. The slide functions by supporting the front drum as the drum rotates. This...

$46.04

Front Drum Bearing

This front drum bearing helps your dryer operate as quietly as possible. It is about 10 inches in height and 22 inches in width. It is made entirely out of plastic and is white in color. If your dryer model has a light in it, remove the light bulb before removing the bearing because it will hit the bulb and potentially shatter it. This is an OEM part and is sold individually. Please note that although the slides are not included in this part, the drum slides should also be replaced when replacing this bearing.

$6.34

Duct Felt Seal

This is a duct felt seal for a dryer. The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum fe...

$4.69

D-Shaped Knob Insert Clip

This clip ensures that the knob is securely fastened to the control shaft, allowing you to properly select the correct time and setting for your dryer. If your dryer will not start or shut off, the timer will not advance, or the dryer shuts off too soon, the issue may be the control knob itself. This part is sold individually. Although this part fits with some different brands, be sure to check the list of brands below to make sure it fits with your dryer unit. Refer to the manual provided by the manufacturer for further installation instructions.

$24.29

Drive Belt

This is a dryer drum drive belt. It is 89.5 inches long with four ribs on the inside for a better grip. The drive belt on your dryer attaches to the motor pulley and then wraps aro...

$53.22

Rear Drum Bearing Kit

This rear drum bearing kit includes a shaft, ground strap, bearing, seven screws, and installation instructions. The bearing plate comes with a slot in it for the ground strap. This part helps keep your dryer running as smoothly as possible with as little noise as possible by supporting the back of the dryer drum and reducing friction as the drum rotates. Over time, your drum bearing will wear out, cause your dryer to be noisy, and you will have to replace it. There may be some sharp internal parts, so be sure to wear work gloves during repair.

$38.71

Cycling Thermostat - 4 Wire

This thermostat helps to regulate the dryer's internal temperature. L210-30F

$37.98

Rotary Start Switch

This part is used to start the dryer once you have selected a setting on the timer.

$69.06

Lint Trap Duct Assembly

This part includes the duct felt seal (PS9861764) and gasket (PS2577674). NOTE: Per manufacturer this part no longer comes with the sensor bars.

$18.68

Idler Pulley Wheel

A dryer's idler pulley wheel serves to help the belt to rotate the drum.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

original duct was broken

  • Customer: Chad from Gilbert, SC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 123 of 141 people found this instruction helpful
Dear PartSelect.com,

My repair went off without a hitch.

2 screws removed to remove top.
4 screws removed from inside to remove front panel w/ door.
4 screws removed from top of control panel, loosed and popped top right off.
Flathead screwdriver to pop off old plastic panel.
Removed old wire chase (plastic, approx 3... read more

Dryer would get very hot and then turn off

  • Customer: David from Auburn, MA
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 255 of 537 people found this instruction helpful
It was actually my father, he doesn't use the internet. He thought that because the dyer got real hot and then shut off he thought the thermostat wasn't working and the high temp shutoff was okay. He went through the manual and found the part and took it out. He called the service number but they wanted $50 dollars plus shipping. I saw it was a Thermo-disc p... read more

Drum belt broke

  • Customer: Adrian from Middletown, MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 133 of 180 people found this instruction helpful
Removed the front Dryer panel. Left drum in place and lifted it up slightly to get access to motor drive. Slipped belt in place and put panel back on.
This was a first attempt ever at fixing an appliance and it was no big deal. read more