CWG3600AAS Maytag Wall Oven - Instructions

Look in the oven. On the upper left corner is the sensor. Remove two screws. Gently pull the wire and connector through the hole and insulation. Disconnect old sensor, replace new. Gently push the connection through, then finish pulling through from behind the stove. Replace the screws inside the oven. Done.

Purchased 2 piece broiler pan from this site

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then conected the new element and replaced te two screws. Turned on the oven & works fine.
Very Easy!

. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) pushed wires back in and secured sensor

i needed a rack for my oven i looked everywhere for one that fit could not find one.my oven is not common due to the fact it is for a very small space and only 18 " wide i stumbled on this site by accident and decided to try it out shipping was very fast and people there are very nice any have alot of knoldge about parts it is very well set up to order with just a modle # i have told my whole familey about this site they did a great job and i will be back for more parts.

Remove the oven racks. Slide the two catches, located at each rear corner of the oven bottom, toward the front of the oven.

Lift the rear edge of the oven bottom slightly, then slide it back until the front edge of the oven bottom clears the oven front frame. Remove oven bottom from oven.

Pulled storage drawer out to the first stop position. Lift up front of drawer and pull to the second stop position.
Grasp sides and lift up and out.

Under storage area, I removed two screws to remove a steel plate. In the oven, I removed two screws that held on the Oven Igniter. Unplugged the Igniter under the storage area.

Plugged in the new Oven Igniter, replace the two screws that held the Oven Igniter, replace the two screws for the steel plate. Put the storage drawer back, the bottom of the oven back and the racks.

It was easier than I though it would be.

The repair was easy. Partselect processed my order quickly and my part was delivered sooner than I expected.

Removing the old igniter was simple. I took off the oven door to create easy access to the oven. I then unplugged the connection and removed the screws that held the older igniter in place. Installing the new igniter was almost as easy. I followed the same steps as above, but in reverse. I accidentally dropped one of the screws, so installation probably took 1 minute longer than removal. :)

I'm a very satisfied customer.

I removed the two screws that attach the sensor to the oven wall. Then removed to more screws in the back of the oven and took off the rear cover, diconnected the sensor connector and installed the new sensor.

After reading some of the repair stories, I was hesitant about doing this task. It was really very simple, I just removed the screws from the back of the stove, and removed the old element. I then replaced it with the new one and replaced the back cover. This whole task from start to finish took 10 minutes. The oven heats perfectly now just like a new oven.

Had to unplug unit, remove back of unit (6 screws), then unscrew oven sensor (2 screws), then unplugged old sensor, replaced it and put back of oven on...Moving the oven out and working in the tight space avaialble was the most difficult. Other than that, super easy job that probably saved me a lot of $$$...

The repair was easy. The door pulls off the hinges without any tools. I had to remove four screws ihat held the wall oven in place. I then removed approximately eight trim screws to expose the two screws holding the hinge in place.I then needed to utilize a nut driver to put the screws in the new hinges because the screws cut threads into the hinge as you put them in so they are a little tight and the nut driver makes this step easier.

First I removed the burner to which the igniter was attached to. Then I attempted to removed the two screws holding the igniter in place. However, these screws proved to be difficult. I called a local appliance repair shop and the person I spoke to explained how the screws were designed to go one way. Any attempt to remove these screws would result in the threading to be stripped and virtually impossible to remove. (I have never heard of these type of screws before) Anyway, he recommended a hack-saw. Well, the hack-saw worked. After that, the replacing of the part was very easy. Igniter works perfectly and now my wife is ready to conquer the bake sales.
This was my first time using partselect.com.
Yes, I will recommend them to other homeowners.
Thanks. A.T

I located the igniter element, and remove the two screws that hold it in place. I then went around to the back of the oven and located the wire, and disconnected it. Then I pulled it out through the oven and removed it. I then replaced it with the new element; pushed the wires through to back of the stove and plugged it in. With that done, I screwed the new igniter element into place. I then put my oven back together; pushed it back into place and turned the gas back on. And presto! my oven lights like new again. I saved myself the costly repairman visit, and the job was easy.

Removed back of stove, removed screws from sensor inside oven, unplugged connector from back of stove, pulled sensor out through oven; installed new sensor, replaced back of stove. Set the oven to bake, waited for it to pre-heat; the oven thermometer showed that the same problem was occurring, the sensor replacement didn't work.

After shutting the main valve behind stove. Removed all shelves and rear cover from stove. Unplugged the plug to the sensor. Removed the two mounting screws and pulled the old sensor out. Installed new sensor and plugged it in again. After reinstalling the rear cover and shelves, replugged in power, openned the gas valve behind the stove and tested with soapy water to make sure there wasn't ant developed leaks. Turned on oven with a test thermometer in it. Monitored operation and now oven temperature is roughly 10 to 20 degrees to the setpoint.