Quick Question!

Have you ever purchased from PartSelect.com before?

Models > CW2079CWD > Parts

CW2079CWD (WD-10460BD) LG Washer - Parts

All parts for the LG Washer CW2079CWD

Below is a list of all parts for the LG Washer CW2079CWD - Commercial WASHER. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the CW2079CWD
1-14 of 97
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$69.64

Drain Pump and Motor Assembly

The drain pump and motor assembly may also be known as the washer drain pump, and is a part for your washer. The function of this assembly is to help expel water from the washing m...

$22.05

Water Inlet Valve - Hot

The hot water inlet valve on your washing machine controls the water flow into the washer. This inlet valve has a standard hose fitting inlet and one water outlet. The water inlet valve opens to allow water to enter the washing machine. If the water inlet valve is defective, the washer may leak, fill slowly, or not fill at all. To test your valve, unplug the washer when the symptom occurs. If the washer continues to fill, then your inlet valve is defective. This part is approximately 3 inches long x 3 inches wide.

$41.14

Tub Bearing

The tub bearing supports the spin basket shaft at the back of the washing tub. If your washing machine will not spin, is leaking water, or if there is a loud screeching noise durin...

$31.78

Tub Bearing

This is known as a tub bearing or a rear bearing, and it is part for your washing machine. The function of this bearing is to be a support for the spin basket shaft that is located at the back of the washer tub. This model is sold individually and measures to have a 2.5-inch outer diameter. As this bearing is very difficult to install, the manufacturer recommends completely replacing the rear tub and bearing assembly. If you are only installing the rear bearing, consider replacing the seal and the other bearing as they wear out together.

$11.85

Gasket

If you notice your washing machine is leaking water from the top of the transmission, it might be due to the gasket being damaged or worn down. When replacing your gasket, consider...

$46.54

Switch Assembly,Locker

The locker switch assembly is a part for your washing machine and tells the washer that the door is closed and locked into place. If the switch has shorted out and not locking, it is no longer delivering the message to the machine and it will not latch into place. If you find that your door will not close, open, or start, it is more than likely an issue with the locker switch assembly. The switch is located behind the front panel. You will need to remove the gasket to reach the switch.

$13.88

Locking Pin

This is a locking pin, and it works in conjunction with your washer. The part measures to be roughly 3 inches long, and less than an inch wide. The pin is cylindrical, off-white in...

$22.05

Tub-to-Pump Drain Hose

This is a tub-to-pump drain hose for a front load washer. The hose features flexible bellows which allow it to expand and contract when necessary. It carries the water from the tub of the washer to the drain pump so the used water can properly empty from the tub. This part is made of rubber, is black in color and measures 13 inches long. Be sure to drain the excess water from the washer before completing this repair. This is an authentic OEM part that is sourced directly from the manufacturer.

$22.05

Shock Absorber Kit

This kit includes 1 shock absorber and 2 pins.

$11.85

Gasket

This is a seal for a washer tub. It creates a seal between the front and rear halves of the washer tub to prevent the appliance from leaking. If you notice leakage between the two sections of the tub, you may need to replace this part. Seals can get dry and brittle over time which compromises the integrity of the part and may cause your appliance to leak. This is a genuine replacement part sourced from the original manufacturer. You will need to disassemble the outer panels of the washer to access the tub seal.

$81.56

Door Gasket

Also known as a door boot seal or bellow and comes with a drain hole.

$28.71

Sensor Assembly

$102.43

Spider

$22.05

Washer Hose with Bellows

This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose connects the dispenser assembly to the tub. Before beginning the repair, unplug the washer and turn off the water supply. You will need a Phillips head screwdriver to complete this repair; a clamp tool can also be helpful. Remove the screws holding the lid of the washer in place, and take off the lid. Locate the dispenser hose and remove its clamps. Place the clamps on the new hose, using the arrows for a guide in positioning the clamps. Install the new hose and reassemble all other parts.

All Parts for the CW2079CWD
1-14 of 97