CSD2525ARB Magic Chef Refrigerator - Instructions

An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only swing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.

Very simple repair. First Remove ice tray. Next remove enclosure. Believe there were 3 screws to remove enclosure (1 bottom, 2 top). Slide enclosure out slowly to gain access to power connector mounted on back wall. removed components from enclosure (motor and solenoid). Take extra care removing solenoid with spring/rod as it is 3 separate pieces (spring, rod, and coil). Easy to figure out reassemble but easier if you take note during disassembly. Took me a while to get yoke off from motor assmbly. noticed they were reverse threads (lefty). So to remove yoke from shaft had to turn CW vs CCW on regular threads. Once had yoke off, rest of assembly was easy. Mounted motor, reinstalled yoke. Put entire re-assembled enclosure back in fridge. Slide in part way, to give yourself plenty of room to plug power connector in. Reattach assembly with 3 screws. Works like a champ.

The tiny piece of plastic that holds the wire that shuts off the icemaker, broke early on with our fridge (after just a few months.) We superglued it, but last week it bit the dust for good.

Once I got this part, I removed the freezer door and trays, and pulled the icemaker out by removing 3 flathead screws and unplugging the cables. Laying in the freezer on the floor was a bit unconfortable, but not too bad.

Then I inspected the icemaker. There was no obvious way to remove the part without disassembling the front of the unit (where the motor is) to release the spindle and free the part, so I did that - 3 or 4 nuts was all that held it together. Once that was out, I removed the spindle, swapped out the part, and put it all back together and back in the freezer. Plugged it in and waited.

It took a while to start making ice. Like 5 hours. Now it's going pretty slow (much slower than before.) Haven't had time to look into it, but my suspicion is the rubber hose that feeds water into the icemaker is blocked with ice or kinked. In any case, we have ice now (but not a lot), and the unit shuts itself off properly. However, we went from having too much ice (thing never shut off) to too little (thing makes ice too slow), so I need to shoot for somewhere in the middle ;)

Once I saw the replacement part I understood how to pry out the switch with a small screwdriver. Then just unplug the old one, plug in the new one and pop it into place.

The PartSelect site made it easy to correctly identify the correct part, it was inexpensive, and the shipping was fast.

I'm very pleased!

First I removed the Ice bin, I then loosened the ice bin rail under the ice maker and removed the screw that attached the bottom of the ice maker to the side of the fridge. I unplugged the power to Ice Maker from the back of the fridge and unscreewed the two screws that secured the ice maker to the fridge. This allowed the Ice Maker to be removed from the fridge. To replace the new ice maker I simply repeated the steps in reverse.

Philips head screwdriver and ten minutes was all it took! I removed the two screws that hold the icemaker assembly in place, then pulled it out a little and disconnected the electrical plug freeing the icemaker assembly. Then I snapped the external parts off my old icemaker assembly and snapped them on the new icemaker assembly. Installing the new icemaker assembly was just as fast and easy. I snapped the electrical plug into the new icemaker assembly, then screwed in the two screws. It was making ice shortly thereafter. Glob free ice! I'm glad I didn't call a repairman. I probably saved a hundred bucks. A ten year old could accomplish this simple and easy task. No wonder the Maytag repairman has time on his hands.

Several days back I found I couldn't get any ice from the ice maker. I was able to hear noise from the ice maker but no ice would dispense. I opened the freezer and removed the ice bucket to find out that the Auger has broken off from it's plastic housing in the back of the freezer. I went to partselect.com to find the part(s) that were broken, it was much easier because of the diagram/images they have for each individual section of the fridge. Parts came quickly and as expected.

The replacement of the auger motor is very easy if you follow these steps:

1 - Remove the ice bucket from the freezer
2 - Unscrew the one screw on the bottom left side of the ice bucket tray (the tray holds the ice bucket in place). I used a small needle nose plier to remove this screw as I was having a hard time with my drill or wrench set. After you've removed the one small screw, lift the tray up and slowly pull towards you.
4 - You'll quickly see that the auger motor and magnetically controlled yoke are connected with a wire harness to the back of the freezer.
5 - Gently crimp the ends of the wiring harness connector with your hand and slowly pry away from the freezer. Once you've removed the wiring harness you can remove the entire tray with the parts attached (yoke/auger)
6 - Unscrew the auger motor from the tray. You'll also have to remove the auger from the motor else it won't come out. In my case the whole plastic attachment was broken so I didn't have to do this (ie I replaced the ice tray as well). It was impossible for me to remove the auger from the auger motor, not sure why the auger was so tightly attached to the motor - it could be the reason the auger motor broke from the ice tray?, so I had to buy a brand new auger motor and auger (ie Auger Drive Motor Kit). I hope you have more luck then I did removing the auger. If you can't remove it you'll need to buy the Drive Motor Kit (which comes with the drive motor, detached auger and auger washer).
7 - Once/if you've removed the auger from the motor and remove the motor from the ice tray, you can proceed with the replacement of motor.
8 - Using needle nose pliers remove the three power connections on the motor (white/neutral?, pink/power?, green/ground, note where the connections were when you removed them because you'll replace them in the same place on the new motor).
9 - Attach new motor to ice tray with the four screws, attach the auger and auger washer to the auger motor, attach the power connections back (white, pink, green).
10 - Re-connect the wire harness to the back of the freezer
11 - Move ice tray back into place, and attach the one screw back to the ice tray to hold it in place.
12 - Replace the ice bucket back onto the ice tray
13 - Done, you should now get ice!

Good luck, I hope this helps. It's easy and you don't have to pay three times this price to replace these ice bucket parts.

The new Ice Maker Assembly arived in less than 24 hours. I was amazed that it came so fast.

I had already removed the old ice maker in order to get the modle number.

I just took two parts off of the old ice maker and quickly snapped them into place on the new ice maker. Then attached it to the refrigerator in less than 10 minutes. With in a few hours I had ice again !!!!!

I would definatly use partselect.com again.

Removed housing on the freezer side and removed the assembly by removing the two bottom clips and then unclipping the wire harness, two prong, and replaced as remvoved. Power was off of course. Watched for 24 hours and recovered housing and its been working great.

I noticed that the thin plastic flap was missing. I squeezed the housing, unsnapped and pulled. INstalling the new part was just the reverse. No more frozen vegetables.

tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened the screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!

The old icemaker had a bad motor and would stall in the fill cycle causing my kitchen to flood on occasion.

The new one was so quiet, I thought it didn't work!

Anyway, one nutdriver and 5 minutes and I had the new one in there... It is so quiet, and I always have plenty of ice now!!!

Thanks!!!

First I unplugged the refrigerator, then next I removed the (4) screws holding in the inside back panel section of the freezer covering the cooling coils, the fan motor is attached to the removable panel.
I then unplugged the wiring harness to the fan motor which allows you to completely remove the freezer inside panel in order to replace the fan motor on a counter top or benchtop.
I removed the (3) spade terminal wiring from the fan motor and the nuts holding the motor on the frame. I then replaced the fan motor and blade the same way I had removed the old one, and then reattached the wiring terminals on the same terminals as the existing motor, making sure that black, red, and green do not get mixed up. I placed the rear panel back inside freezer and plugged in the wiring harness, fit panel back to original position and reinstalled the (4) panel screws. I once again plugged in the refrigerator and restored power. Everything is working fine.

I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt