CFD28WIS0 Crosley Refrigerator - Instructions

First I pulled the ice tray out so I could see the solenoid housing/ice tray support(1 unit). Below the ice tray there are 2 screws that hold the solenoid housing/ice tray support. After removing those the assembly lifts up so you can see the wiring harness to disconnect. I pulled it out and removed the 2 screws to open it up. There is 2 screws holding the solenoid in place and one ground wire. This was an easy fix and I know I saved a lot of money.

I checked the dampener, it worked. The compressor and fan worked. I knew because my freezer was still hovering around 10 degrees. Coils were clean. Thermistor was the only thing it could be. Took all my shelves out. Removed four screws. Took the back panel off. The thermistor sits tucked in on the side. I piped it out, in clipped it. Used my multimeter to test the numbers. Numbers were off just a bit. Ordered the part. Crossed my fingers.,took less then 5 minutes to put the part in. Plugged in the fridge. It was sitting at 33 degrees in about an hour and a half. I can’t believe I fixed it. I knew NOTHING about refrigerators. For how big my fridge is, it would have cost 3,000 and up to get a new one with the same cu ft size. Instead, it cost me $44. That includes shipping. Thank you Parts Select!! Made it so easy to pick the correct part for my model fridge!

Pulled the old gasket out if groove on the door, cleaned inside the groove, squirted some windex in the groove to ease the new gasket in the groove, then proceeded to work the gasket into the groove. Made sure gasket was all the way in the groove around the perimeter of the door. Done!

push in old filter, turned to the left and filter came out. Pushed in new filter and it clicked into place. Very easy to do.

removed fan unit from frig and installed new motor and then replaced back in frig. No tools needed. need to unplug unit and take apart and put new motor in the unit and then plug back in.

To confirm my diagnosis I first replace the filter still no water flow.
Check water supply from the wall valve: ok
Remove the entire inlet valve assembly and sit it over a small bucket.
Disconnect the tubing from the bottom of the 1st selenide valve: this is the one leading to the filter.
Place cup under water dispenser and activate dispenser. No water discharge from inlet valve confirm valve is bad.
Install the new valve matching the colored tubing with the color on each inlet valve.
Re-connect the water supply place container under water dispenser and activate: There will be a large gush of air then water. Dispense aprox 1 gallon of water to confirm all the air is purged from the system. Your refrigerator is now back to dispensing water and making ice.
Good luck everyone - Neville

The instructions that were provided were perfect. Easy step by step. Entire installation took only 15 minutes

Replace gasket

The part i recieved, from parts select was a larger in circumfrence (<1/4) than the original. However i was not aware of this until after i treid to repair it.

I removed the broken fan from the condenser. This was very sipmle.

When i pluged the refridgerator back in to the outlet the fan tried to start up but soon began to make aloud noise, due to there not being enough clerance.

Took drawers out by removing 2 screws on top of rail near front, then popped black plastic cover off in lower right inside cabinet...sensor just un plugged and new one plugged in easily...did not fix problem though...display set at 34 but bottom drawer reads about 40 at best and upper drawer reads around 55...dont think the 3 little fans inside on back wall have been running

Took the broken drawer out and easily slipped the new one in. Fits perfectly.

Disconnect the two water supply tubes at the base of the Water Filter Base. Using a 7/16" open end wrench, press up on the blue "O" rings to disconnect the tubes. Use a Using an 8" long magnetic phillips head screw driver I was able to unscrew the 4 short screws holding the original water filter base and the immovable attached water filter. Replacement was easy. Simply slide the new base into the fixed slot on the refrigerator and reinstall the 4 holding screws. Reconnect the water supply tubes to the Water Filter Base. Install a new water filter.

Did not repair, sensor was not located where you said, wrong sensor was sent to me, can't return oe exchange it COSTERMER SERVICE WILL NOT ANSWER MY EMAILS.

first, there many different water filters. your experience will be different according to your water filter type.

Removed the previous water filter. Installed the new water filter.
I then filled a large glass full of water from the water dispenser several times to clear the air from the filter and lines.

Time to install, less than 8 minutes.

Thank you Parts Select!