CCE1400W-C Jenn-Air Cooktop - Instructions

Shut off power at breaker box. Removed top burner unit. Removed old receptacle (Mounting screw was rusty so I drilld out the old one.) Cut wires from old unit. Stripped wires back on old unit. Attached old and new wire with ceramic wire nut. Attached new unit. Reinserted top unit. Reconnected power and "voila". Wife was smiling again.

First turn off the power to the stove/oven. Next I removed the 4 screws located on the bottom surface of the control panel. You need to open the oven door to see/access them. The control panel can then be removed by rotating the bottom outward which allows the flange on the top to disengage. Next remove the two screws that hold the switch to the control panel. Note which wire goes to which spade connector. A quick photo can help. Undo the wires. Remove the old switch. Reinstall the wires. Mount the new switch to the control panel. Mount the control panel back into the stove/oven. Turn on the power and test. The burner now works as new!

10 Minutes for a stove my landlord thought was not fixable (repairman had already cut the wires to the element and capped them)! The delivery person handed me the package, I got out the single tool needed, installed the part, put away the tool, cleaned my hands, and put a pot of water on the stove to boil for pasta. 10 minutes!

Well, I had to search a bit deeper in the internet to find out that the problem was not with the surface burner (which did look a bit burned out anyway) but rather with the surface burner switch (Part Number: PS336885) which must have ben damaged by the heat of the closest burner. If this problem would have been better documented (or if I would have searched more carefully) I would have saved over $40 with parts (Surface Burner Receptacle Kit) that I didn't quite need. Repairing the switch was very easy, thanks also to the available video , even though the stove used on this video (front panel) didn't quite match mine (top-back panel).

Starting by me making a substitute prong to keep the stove working while the part this coming by mail. was a piece of cake.

I unplugged the old ones and put in the new ones.

First turn off breaker, then take screws out switch assembly,take oid switch out, put new switch on,turn power on.

In response to your question.......everything went perfectly!! The reason?? I read the directions that were very easy to follow. It was a quick, easy repair, and the stove burner is working like new.

Thank you for your help!!

Bob

Removed 4 screws, tilted cover up and lifted out, removed wires from switch, removed 2 screws holding switch, lifted switch out. Replaced with new switch, connected wires, secured cover with the 4 screws. It worked!

Shut off breaker, removed the top by unscrewing the retaining screws and removing all knobs and grommets. Removed control from top panel by unscrewing, removed 5 wires and placed on new control. I then remounted the control, placed the top in its well, fastened. Replaced the retaining screws in the hold down strip and replaced grommets and knobs. Returned power to panel by turning the breaker on and tested. Used later that evening to grill 2 panini.

The repair itself is really quite easy. Cut the wires, strip the ends and attach the new receptacle with wire nuts. The hard part was getting to it. My cooktop is about 30 years old, so I had to wade through piles of nasty built up grease. Some of the sheet metal screws were unworkable, so I had to cut them off with a Dremel tool. Not a pretty picture, but that's how repair work is on old stuff.

The video on your website showed me how to take out 1 screw, cut the existing wires and strip the ends. The kit came with 2 porcelan wire nuts to re-connect the wires and it was done. Less than 10 minutes. It saved me $100.00 to get it repaired.I bought 2 in case I need another one in the future.They only cost $11.00 each. Awesome website.

took old screw out of stove top that held them in and cut the two wires off close to the burner stripped the wires and used the screw caps to put each line together it doesn't matter which line goes where and screwed it back on with the old screw and tried the two burners and they both worked job done ps it took longer for me to type this but i am slow at typing

It was a very easy project...Removed the stove top a few screws..snipped a couple of wires and attached the new receptacle...everything needed was in the package...They even have a video on here that was very helpful..shows how easy it really is...

The video you provided was excellent! Turned the circuit breaker off. Removed four screws, pulled out control panel, took a picture of the wiring to be safe. Disconnected the wires from the damaged control and removed it (two screws removed). Mounted the new control, connected the wiring, replaced the control panel and the four screws. Circuit breaker back on, turn burner on. That's it. Thanks for the video!