Models
>
BC210
BC210 ((41ADZ22C912)(2014)) Cub Cadet Trimmer - Overview
Sections of the BC210
[Viewing 2 of 2]Keep searches simple, eg. "belt" or "pump".
Carburetor
PartSelect #: PS9119300
Manufacturer #: 753-06190
It is an authentic manufacturer-sourced replacement part that i supplied for Craftsman trimmers. The function of a carburetor is to mix the air and the gas into a highly combustible mix before it goes...
$34.03
In Stock
Pawl Assembly
PartSelect #: PS9457214
Manufacturer #: 753-06091
The pawl assembly is a complete OEM kit that includes the two plastic pawls, the two springs, and the metal housing. Installation is rated "Medium" difficulty and requires a screwdriver and socket set...
No Longer Available
Clutch Assembly, Small
PartSelect #: PS9303676
Manufacturer #: 753-05860
This clutch assembly is a genuine OEM replacement kit for outdoor lawn equipment. The kit includes the clutch drum, clutch, clutch washer, and screw. The clutch assembly transfers power from the engin...
$24.60
In Stock
Switch
PartSelect #: PS10014381
Manufacturer #: 791-182405
This Switch is a black, plastic on/off switch for a trimmer. Installation of this manufacturer-certified switch is rated as "Easy" and requires a screwdriver, wrench set and socket set. Refer to your ...
$10.15
In Stock
Upper Drive Shaft Housing Assembly
PartSelect #: PS9457464
Manufacturer #: 753-06682
No Longer Available
Questions And Answers for BC210
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the BC210
[Viewing 1 of 1]Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
string trimmer would not start
emptied fuel from tank. pulled off the 2 fuel lines from the carburetor.opened the air cleaner door. removed the 2 torque screws that hold on the carburetor. removed the carburetor and air cleaner gasket. installed new carburetor and gasket and put back and tightened the 2 torque screws. closed air cleaner door and pushed the fuel lines o
... Read more
nto the new carburetor.put some fuel in the tank. started the trimmer. runs great.
Read less
Parts Used:
-
john from SHARPSVILLE, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
4 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Carburetor replacement
Removed 2 screws securing the air cleaner and carburetor to the engine using a T25 Torx driver. then removed the throttle cable from the carb.Then removed the o ring gasket from the engine and replaced with a new one and replaced the carb etc. Primed it and fired it up.Runs just like new.
Parts Used:
-
William from PALMETTO, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
7 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Trimmer Would Not Start
The replacement of the carburetor, O-ring, and gasket was simple. I removed 2 screws that held the air cleaner and carburetor in place, swapped them out, and replaced the screws. What took longest was finding a piece of fuel line after breaking one of them. It was brittle after hanging in my garage for several years. I found some in my
... Read more
garage and replaced it. It took a few pulls to get it started, but ran very smooth.
Additional information: rather than mixing my fuel, I purchased 40:1 pre-mix fuel to prevent gunking up the carburetor in the future. I use it in my other trimmer and have not had any issues.
Additional information: rather than mixing my fuel, I purchased 40:1 pre-mix fuel to prevent gunking up the carburetor in the future. I use it in my other trimmer and have not had any issues.
Read less
Parts Used:
-
Ricardo from FORT WORTH, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!