AOGD2750E (P1132534NE) Amana Wall Oven - Overview
Sections of the AOGD2750E
[Viewing 7 of 7]
.gif "SUPPLEMENTAL INFORMATION Diagram and Parts List for P1132534NE Amana Wall Oven")
Keep searches simple, eg. "belt" or "pump".
2 Piece Broiler Pan
PartSelect #: PS971245
Manufacturer #: 4396923
This is cookware designed for use in your range or oven. It is a two-piece dish that is used to grill or cook food while the broil function is on, meaning it can withstand high temperatures. This set ...
$48.36
In Stock
Range Frame Screw
PartSelect #: PS11743908
Manufacturer #: WP7101P126-60
Sold Individually.
$7.30
In Stock
Stand Mixer Screw
PartSelect #: PS11742292
Manufacturer #: WP4159193
This screw is sold individually.
$8.35
In Stock
Oven Light
PartSelect #: PS11744440
Manufacturer #: WP74011278
This oven light assembly is a little over four inches long and comes with the lens and 660-watt light bulb. Make sure your appliance is unplugged or circuit breaker is off before installing this new p...
$77.42
In Stock
Range Flatstyle Oven Igniter Bake/Broil
PartSelect #: PS11740950
Manufacturer #: WP31939701
This igniter doesn't come with the bracket or the connector. It can be used for either the bake or broil in your appliance.
No Longer Available
Electronic Control Board
PartSelect #: PS2192837
Manufacturer #: Y0309305
This electronic board is located within the control panel.
No Longer Available
Questions And Answers for AOGD2750E
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the AOGD2750E
[Viewing 3 of 3]Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Little to no heat when baking
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Stove Work But Your Oven Won't Get Hot ?
If your stove work's but your oven won't get hot it is your ignigter the ignighter in proper working condition sends a signal to the gas valve saying let the gas flow its ok. When the ignighter quits working it won't let the gas flow and your oven will not get hot. It is an easy fix. Just pull out all of interior parts the racks and th
... Read more
e bottom heat shield the ignighter the white stone looking part that is screwed to the burner with two wires and it really don't matter what way the wires go back one of the wires connects in the back so you will have to pull the oven out. Now you have to clean under it and your done.
Read less
Parts Used:
-
Brian from Cumming, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
16 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven would not light
Removed oven door and burner guard. Removed screws holding ignitor bracket and small panel beneath oven door. Disconnected ignitor wires behind panel and pulled out ignitor. Removed old ignitor from bracket and inserted new unit. Fed wires back down thru tubing and screwed in bracket. Connected wires and replaced panel. (Note: old ignitor
... Read more
glowed but would not pass enough current to operate gas valve)
Read less
Parts Used:
-
MATTHEW from SAN CLEMENTE, CA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
12 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
F1 F2 & F3 error codes
This is a very easy repair as the sensor had 2 screws and slid out of the back of the inside of the oven just enough to hook up the new one. I never had to back the oven out of the wall. It is a 5 minute repair. Ok I did use my son's head lamp from scouts for better light as you have to kill the power to the oven, so no oven light. And yo
... Read more
u can't hold a flashlight and do this alone.
However, I ordered the part before I took the old part out. Don't do that. There are 2 froms of Temp sensors that you can order one male and one female. I did not know that and just ordered what looked to be the right part. It turned out that I needed the female sensor. When I called the folks at part select they were terrific! They sent out the new part the next day and a UPS form via email to send the other part back.
I don't know what a service call would have been but this was very easy. I will go here first for appliance parts. Women can fix stuff too!
However, I ordered the part before I took the old part out. Don't do that. There are 2 froms of Temp sensors that you can order one male and one female. I did not know that and just ordered what looked to be the right part. It turned out that I needed the female sensor. When I called the folks at part select they were terrific! They sent out the new part the next day and a UPS form via email to send the other part back.
I don't know what a service call would have been but this was very easy. I will go here first for appliance parts. Women can fix stuff too!
Read less
Parts Used:
-
Suzanne from Acton, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
12 of 14 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!