88369 Jenn-Air Range - Instructions

I ordered part one day, recieved part the next day. I installed it the next day. It worked perfect. THANK YOU!

Replaced surface unit infinite switch

I have a newer jenn air with the 3 prong elements. The original element was 3 prong 1900W only using one of the controls. Since the stove socket would accommodate 4 prongs I looked up the part for the older stoves (PS2357533)which had 2 elemants using both controls. The element plugged right in and I now have high heat like on my older models and it now grills like it should instead of just heating the stuff up. Highly recommended. One caution you will need a metal piece to support the element since the newer stoves do not use the metal bricketts with supports.

Simply pull off the old ones and replace with the new ones. Problem was finding the correct knobs with the double "s" shaft fitting.The item number indicated by the model number was incorrect. I saw a kit with four knobs on your web site and ordered the kit and not the recommended item. Turned out to be the right move and the knobs fir just fine.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Placed new burner knobs onto cooktop. easy

De-energized appliance power at it's circuit breaker. Removed control panel access cover. Removed control panel. Removed old thermostat and installed new thermostat. Reset control panel and access cover. Reset appliance circuit breaker. Confirmed thermostat operation.

After a long time being without a working stovetop-an electrician friend said we needed to change a switch-it was ordered and came very quickly and installed-then it was determined that we needed a switch for the other side of the stovetop-I ordered it and got it the next day! It was a joy cooking thanksgiving dinner on a stove that worked-and I have a new friend that is interested in seeing me on a more regular basis. I know if I needed any kind of parts, I would check with partselect first ;)

Unfortunately it was the wrong part I replaced the infinite switch and had the same problem so I am still trouble shooting but I plan to continue to use parts select they are excellent to work with and very quick to deliver parts

Replacing the switch was quick and easy. It actually took only about two minutes.

took new element out of box, inserted it into stovetop, everything was over in about 2 minutes. It worked just fine.

follow the EASY to read and understand instructions.replaced all 4 controls in about 35 min.

I used process of elimination to figure out the issue with my 28 year old Jenn-Air cooktop. Issue: One day while cooking there was a loud pop & from then the front burner no longer had any temp control & only heated to full blast plus. Steps to fix: 1) Replaced the surface burner elements PS2195246 - this didn't fix the issue but they look nicer now. This was a simple plug in - no tools needed. 2) Replaced the grill side with a 2 burner plug in part PS1941381. Also simple plug in with no tools required. This didn't fix the isssue & I found that the front burner on the new unit also had no temp control. 3) Replaced the Surface Burner Receptacles for the 2 original burners PS1570190. This required turning off the breaker, removing the cooktop by unscrewing all the little screws & then cutting the old connections with wire cutters and wiring the new parts in with wire nuts & electrical tape. It took maybe half an hour but did not fix the issue. 4) Replaced the Surface Unit Infinite Switch Kit PS2076107 for the front 2 burners. Removed the screws just for the center control panel (after turning off the breaker) then took a picture of the wire configuration & removed the old parts by pulling (hard) at the connections until they unplugged. Put the new part in with the same wire placement. This finally fixed the issue & we now have 4 working burners for the first time in the >1 year that we have lived in this house.

Turn off power to cooktop. Lift the broken infinite switch knob off the switch console. Use pliers to remove the hex nut that is under the knob. Then remove the grill over the exhaust vent to expose the two screws that hold the switch console in place. Using a philips head screwdriver, unscrew the two screws and lift the console up as far as the wiring will let you. Push the two little clips on either side of the electrical component you want to replace, to release it from its harness. Pay attention to the wires of the broken switch and pull one off at a time and attach to the new part. I used a knife to pry the wires off the electrical pins. Once all wires are reattached, clip the component into the harness and attach the hex nut back onto the protruding d-stem. Put all back together and test the switch before turning power back on. If ok, turn power on and test again.

Great company....Fast delivery.