61004754 Kenmore Refrigerator - Instructions

Exchange both water valves with new (took me 5 min.)- same brand as original. Nothing else works better. Dont wast your money for Amazon parts or after market.

Unplugged refrigerator. Removed 3 screws holding unit in place. Carefully disconnected the wire from the control face plate. removed existing ice dispense door and spring, disconnected lead from solenoid which controls ice dispenser door opening and closing. Removed 2 screws holding solenoid in place. Removed old solenoid and replaced with new one. Installed new ice dispenser door and spring. Replaced old actuator pad with new one and reassembled.
Repair was easy but unfortunately did not fix the problem. Subsequent tests indicate no power getting to the solenoid so I think I have a circuit board problem --

Turned of power and water to unit. Removed water lines and electrical wires to old valves, tagged wires and hoses before removing. Cut old hose and installed new hose kit. Change from two water lines to one. Remove old valves and replace with new, reinstall water and electrical wires.Turn on water to check for leaks if there are no leaks turn power back on and check for water going to ice maker. A really easy repair.

Just had to follow the easy to read instructions that came with the kit assembly. Only problem came when reinstalling the spring the recomended half a turn of tenison. seems like it was'nt enough tenison to completey close the door air tight. Would be much easier if the pictures where clearer and larger for older eyes to see.

Followed the directions provided with the solenoid and door kit to replace solenoid, door and actuator. Replacing bracket was intuitive, just required transferring of parts from one to the other (miro-switch, cabling, light socket, and circuit board), and then installing the actuator pad on it.

Removed screws, removed parts, spring popped off, didn't know where it was actually at, had a difficult time getting the spring in the right place, (the directions were not that clear), put back together 6 times before I got it right.

Removed 4 screws and disconnect the circuit board, replaced the broken door and reassembled the unit. Solenoid did not need to be replaced, only the ice door. About 15 minutes and about 90$ saved in labor.

removed the panel to get to icemaker(4 screws), then removed the plug, then removed worn solenoid and replaced with
new one. Had to jiggle old solenoid to get out,
but not with much effort. Everything went back
into place effortlessly

Replaced the old part with the new one and we're back in business again plenty of ice.

easy, step-by-step repair. replaced all parts that came with kit; no hastle. only issue was that "torx" head screwdriver was needed (which I had).

The Refrigerator had panels of wood, they had to be removed above the Ice maker face plate before it could be lifted off. There were several layers of Torx screws to be taken off., had to purchase that tool. Luckily they were all T-15 and I guessed right at the hardware store. The rest of the repair went pretty as indicated on the sheet provided.

I removed the two screws from the front door panel, unhooked the wire, removed three more screws and removed the broken door. I replaced the door and replaced everything in reversed order. I did not need to replace the solenoid so I still have that if needed in the future, The instructions were so easy, it took less than 5 minutes and I estimate saving about $90.00 on a sevice call after deducting the cost of the part from PartSelect.
I will check out PartSelect for future repair jobs.

Thanks

I just followed the directions that came with the part and it was very simple. Saved at least $100 on the repair. Anyone could do this repair. Don't call Maytag.

directions in package really made it easy. Saved $175.00

Pulled out frig and unplugged it from wall. Took out 2 screws to gain access to valves. Took out screw holding bracket holding valve bracket to frig and removed one more to remove the old valve from bracket. Simple water disconnect with wrench after that and changing the lines to door cutting them back 1/2 ", direct plug in electrical connections, replacement exact like original. I had previously changed the other solinoid with the problematic Y connector but that didn't do the trick. This fix seems to be the correct one to fix the problem.