4860 - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
the element plugged in, stove was woking right away.
The element plugged in to the cook- top.The cook -top was working moments after i unpacked the element. thank you.
Jim B.
Jim B.
Parts Used:
-
James from Frederick, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
5 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The element burned out
Just replaced the element and put new rock grate supports on the rock grates and we're set to grill
Parts Used:
-
Diane from Orlando, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
5 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner temperature control did not work.
Got a no-name tailor-it-yourself replacement switch from a San Jose, CA appliance parts store; but the switch was so cheaply made that it fell apart when I tested it.
Got a RobertShaw part from PartSelect and now the burner works perfectly.
Got a RobertShaw part from PartSelect and now the burner works perfectly.
Parts Used:
-
Gerald from Palo Alto, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers, Wrench (Adjustable)
5 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The 8" burner switch would operate both the 6" and 8" burner.
First pulled the two screws holding the control with the switches. Then I unscrewed the nut holding the 6" burner switch and disconnected the wires on the switch and replaced the switch with the new one. Replaced the control unit in the range top and tested the repair.
Parts Used:
-
Jack from Carson City, NV
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Wrench (Adjustable)
5 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The control knobs on our otherwise "healthy" Jenn-Air range were worn off and did not turn stove on correctly.
Simply pulled the old ones off and pressed on the new control knobs. It took less than 10 minutes, saved us from replazcing an otherwise nice looking range top, and made a big deposit in my "Honey do" account. I just wish they still sold the clock and timer units to fit this stove. Oh and yes, the prices were very reasonable too. Thank You Brad Harris, Illinois
Parts Used:
-
Brad from Clay City, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light bulb in water ice freezer door went bad
I didn't. Don't know how to get to light bulb to change it for this specific model
Parts Used:
-
Carl from RIVERSIDE, CA
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Screw drivers
7 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Degrees were illegible.
I removed the old knob and replaced it with the new Maytag knob which worked.
I was especially pleased because another website had listed the part as unavailable, and a local parts store said they could not help me. Our range is at least 30 years old.
I was especially pleased because another website had listed the part as unavailable, and a local parts store said they could not help me. Our range is at least 30 years old.
Parts Used:
-
Lois G from Baltimore, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
4 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner would not get hot
removed two screws thenpulled element up unpluged wires
Parts Used:
-
Royal from Gilmer, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
4 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not heat at bottom
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I did a continuity test and determined the old element was bad - ordered the new one and put back the screws. All done!
Parts Used:
-
Wayne from Conifer, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rheostat temperature controller failed. No heat at ring.
Turned off power at breaker. Removed screws holding control knobs in position. Removed knob and unscrewed nut holding switch in place. Noted wire positions and undid connections. Connected wires to new unit. Replaced nut and screws and control knob. Restored power and checked operation. You can do this. Don't call an electrician.
Parts Used:
-
David from Atlanta, GA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench set
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The switch needed to be replaced
I TURNED OFF THE POWER TO THE GRILL FIRST. Then Removed the knob on the top face plate and then removed the 2 self tapping screws at the high end and this allowed the face plate to be pushed forward. And allowed access to remove the switch I removed the wires one at a time and replaced them on the new switch. All done in 20 minutes.
Parts Used:
-
Nora from AUBURN, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed new filter
-
Vincent from Foxboro, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Parts Used:
-
Yafa (and David) from Bothell, WA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
5 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Oven Handle and Missing Indicator Light
Removed the outer cover from the oven door by taking out approx. 9 screws. Cleaned the inside while I had it off. Attached the new handle with two screws (weren't included) had to use old screws. Then reattached the cover.
Replaced the indicator light by removing approx. 4 screws from the control panel. Slipped the new indicator lens in the hole and slid the light socket into place to hold the lens. Reattached the control panel.
Job Complete!
Replaced the indicator light by removing approx. 4 screws from the control panel. Slipped the new indicator lens in the hole and slid the light socket into place to hold the lens. Reattached the control panel.
Job Complete!
Parts Used:
-
Tina from Hernando, MS
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
5 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Element failed
-
Andrew from Salem, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
4 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!