Models
>
44N877
44N877 Engine - Overview
Models starting with 44N877
Click on the best match to narrow your results.
- 44N877 ( 0010-G1 ) Briggs and Stratton Engine (Briggs & Stratton Small Engine Model 44N877/0010-G1 (44N877/0010G1, 44N877/0010 G1) Parts)
- 44N877 ( 0004-G1 ) Briggs and Stratton Engine (Briggs & Stratton Small Engine Model 44N877/0004-G1 (44N877/0004G1, 44N877/0004 G1) Parts)
- 44N877 ( 0005-G1 ) Briggs and Stratton Engine (Briggs & Stratton Small Engine Model 44N877/0005-G1 (44N877/0005G1, 44N877/0005 G1) Parts)
- 44N877 ( 0007-G1 ) Briggs and Stratton Engine (Briggs & Stratton Small Engine Model 44N877/0007-G1 (44N877/0007G1, 44N877/0007 G1) Parts)
- 44N877 ( 0001-G1 ) Briggs and Stratton Engine (Briggs & Stratton Small Engine Model 44N877/0001-G1 (44N877/0001G1, 44N877/0001 G1) Parts)
- 44N877 ( 0011-G1 ) Briggs and Stratton Engine (Briggs & Stratton Small Engine Model 44N877/0011-G1 (44N877/0011G1, 44N877/0011 G1) Parts)
- 44N877 ( 0006-B1 ) Briggs and Stratton Engine (Briggs & Stratton Small Engine Model 44N877/0006-B1 (44N877/0006B1, 44N877/0006 B1) Parts)
- 44N877 ( 0008-G1 ) Briggs and Stratton Engine (Briggs & Stratton Small Engine Model 44N877/0008-G1 (44N877/0008G1, 44N877/0008 G1) Parts)
- 44N877 ( 0015-B1 ) Briggs and Stratton Engine (Briggs & Stratton Small Engine Model 44N877/0015-B1 (44N877/0015B1, 44N877/0015 B1) Parts)
- 44N877 ( 0003-G1 ) Briggs and Stratton Engine (Briggs & Stratton Small Engine Model 44N877/0003-G1 (44N877/0003G1, 44N877/0003 G1) Parts)
- 44N877 ( 0012-G1 ) Briggs and Stratton Engine (Briggs & Stratton Small Engine Model 44N877/0012-G1 (44N877/0012G1, 44N877/0012 G1) Parts)
- 44N877 ( 0014-B1 ) Briggs and Stratton Engine (Briggs & Stratton Small Engine Model 44N877/0014-B1 (44N877/0014B1, 44N877/0014 B1) Parts)
- 44N877 ( 0009-B1 ) Briggs and Stratton Engine (Briggs & Stratton Small Engine Model 44N877/0009-B1 (44N877/0009B1, 44N877/0009 B1) Parts)
- 44N877 ( 0013-G1 ) Briggs and Stratton Engine (Briggs & Stratton Small Engine Model 44N877/0013-G1 (44N877/0013G1, 44N877/0013 G1) Parts)
- 44N877 ( 0002-G1 ) Briggs and Stratton Engine (Briggs & Stratton Small Engine Model 44N877/0002-G1 (44N877/0002G1, 44N877/0002 G1) Parts)
- 44N877-0016-B1 Briggs and Stratton Engine (Engine)
- 44N877-0018-G1 ( 400000 - 699999 ) Briggs and Stratton Engine (44n877-0018-G1)
- 44N877-0018-G1(40,44&49) ( 400000 - 699999 ) Briggs and Stratton Engine (44n877-0018-G1 (40,44 & 49))
- 44N877-0019-G1 ( 400000 - 699999 ) Briggs and Stratton Engine (44n877-0019-G1)
- 44N877-0019-G1(40,44&49) ( 400000 - 699999 ) Briggs and Stratton Engine (44n877-0019-G1 (40,44 & 49))
- 44N877-0020-G1 ( 400000 - 699999 ) Briggs and Stratton Engine (44n877-0020-G1)
- 44N877-0020-G1(40,44&49) ( 400000 - 699999 ) Briggs and Stratton Engine (44n877-0020-G1 (40,44 & 49))
- 44N8770003G1 (2019-09) Husqvarna Engine (Briggs & Stratton Engines (For Us, Au And Nz Only), 44n8770003g1, 2019-09)
- 44N8770005G1 (2019-09) Husqvarna Engine (Briggs & Stratton Engines (For Us, Au And Nz Only), 44n8770005g1, 2019-09)
Keep searches simple, eg. "belt" or "pump".
Aluminum Push Rod
PartSelect #: PS9073139
Manufacturer #: 690982
This is a replacement push rod for your lawn tractor engine. It is made of aluminum and is the push rod used for the exhaust valve. Occasionally, the push rod in your engine can become damaged, and wi...
$8.27
In Stock
Rod-Push (Steel)
PartSelect #: PS9062983
Manufacturer #: 690981
This is a replacement steel push rod for your lawn tractor engine. The engine will have two push rods; one made of steel, and one made of aluminum. This part is made of steel and is approximately 6 in...
$6.89
On Order
Seal--Oil (PTO Side)
PartSelect #: PS9151828
Manufacturer #: 795387
This OEM Seal-Oil (PTO Side), also called the Oil Seal, is a Black, Nitrile Rubber, 2/14 O.D., individually sold part which is installed using a Seal Puller. Customers rate the installation difficulty...
$7.88
On Order
Gasket-CylinderHead
PartSelect #: PS9067184
Manufacturer #: 693997
This is a replacement cylinder head gasket for your small engine. The gasket is approximately 5 inches in length and 5 inches in width at its longest and widest points. The gasket creates a seal, and ...
$26.91
In Stock
Seal,Oil
PartSelect #: PS9277860
Manufacturer #: 391086S
The Oil Seal is a manufacturer-approved rubber part which provides a seal between the crankcase and crankshaft by attaching around the axle shaft on the crankhouse housing. Installation is rated as "M...
$6.59
In Stock
Crankcase Gasket With Bolts
PartSelect #: PS11829358
Manufacturer #: 594195
This genuine crankcase gasket is used on small lawn and garden engines. Its purpose is to make an air tight seal so that no air/oil leakage occurs. Over time this gasket will deteriorate and will need...
$37.66
In Stock
Common Symptoms of models starting with 44N877
[Viewing 1 of 1]Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
governor not working
Had to pull the engine off the rider mower. Drained the oil took shield off the flywheel. Set it upside down on a 5 gal bucket. Took a 7/16 hand wrench to remove governor lever from bottom of engine. Left it in its location. Pulled 10 1/2 " bolts. Split engine case. Found the old governor had broke into pieces. Had to use a magnet t
... Read more
o remove all the pieces. Removed the small clip and removed gear. Lubed shaft slid new on put new clip on. Lined governor weights with center piece tapped it in place very lightly. Cleaned gasket flanges pulled the shaft seal. Used the old seal as a seal driver. When putting the cover back on make sure the seal dont roll out. Take a mini screwdriver and tuck it in around shaft. Put bolts back in and tighten like instructions
Read less
Parts Used:
-
rodney from MUSCATINE, IA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Screw drivers, Socket set
12 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad governor
Look on YouTube for video's on how to replace a Briggs governor. There are several there. My favorite, with best explanation, is, "Easily Replace Briggs Governor Gear (V-Twin Intek Engine) with Taryl". https://www.youtube.com/watch?v=wn3eanGxSEA&t=152s.
Taryl (probably not his real name) does a very good job of showing step-by- ... Read more step the whole procedure, along with some additional hints/tricks/techniques of value.
Not including oil and filter, I spent less than $50 for a new governor, gasket, and drive shaft seal. That's all that is really necessary to replace is those three parts. That is, unless pieces of the old governor tore up a gear, valve, or something else. Inspect everything! {I was lucky and only the governor was destroyed}
One word of note. Be sure to clean out all of the debris from the blown governor. Be sure to remove the spark plugs and carefully rotate the drive shaft while looking for nooks-and-crannies where debris can hide. I tried to use a magnet to help, but it didn't help much, even though the block is aluminum.
Good luck.
Taryl (probably not his real name) does a very good job of showing step-by- ... Read more step the whole procedure, along with some additional hints/tricks/techniques of value.
Not including oil and filter, I spent less than $50 for a new governor, gasket, and drive shaft seal. That's all that is really necessary to replace is those three parts. That is, unless pieces of the old governor tore up a gear, valve, or something else. Inspect everything! {I was lucky and only the governor was destroyed}
One word of note. Be sure to clean out all of the debris from the blown governor. Be sure to remove the spark plugs and carefully rotate the drive shaft while looking for nooks-and-crannies where debris can hide. I tried to use a magnet to help, but it didn't help much, even though the block is aluminum.
Good luck.
Read less
Parts Used:
-
John from BROOKVILLE, IN
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Socket set, Wrench set
5 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
valve problem causing pushrod damage
pinged valve guide reinstalled head with new gasket inserted rods adjusted valve 15 min. later mowing lawn first time doin such repair note used magnet to pull old rod inside engine to drain left in rotated engine maling sure no parts broken started up and away i went c how long it lasts mower had over6500 hrs.. on it
Parts Used:
-
george from HALLWOOD, VA
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers, Socket set, Wrench set
7 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!