3RMTW4905TW0 Maytag Washer - Instructions

The switch just snapped out of the holding section and the new part was snapped back into its place. He put the top section back on and it worked! Being a woman not knowing anything about repairing machines, I thought it went very well. I just googled my problem with the washer, it sent me to this site saying what they thought was the problem, I live chatted with someone and they confirmed the solution. I ordered the part and it came in 2 days and my husband fixed it. And now I have a working washer again. Thank you for your site. Anne

I read the experiences of others on this site and determined that the problem was probably the lid switch. Used others experience in taking the panel off and removed the old switch and inserted the new one. The post to be sure to have the lid open was good and probably saved me some time. Overall, the fix was simple and the problem appears to have been solved. The lid switch got here the day after I ordered it and that was great service. Better than paying for a service call or new washer.

We had to take the motor off and find the part that holds the spring, took longer to fix as we are older people and took a brake after every spring. We used YouTube videos to help us I am thankful for this site and cheap prices.

replaced missing screw and pad and now machine works perfectly

Unplugged the electrical plug and turned off the water. Used putty knife to remove control box. Unplugged the washer lid switch. Used screwdriver to remove clips to washer cover. Removed cover out of the way. Removed clips that hold the drain hose on the washer frame. Used Pliers to open the clip that holds the drain hose on the discharge pump. (You will need to re-use this clip) Removed the bad drain hose. Installed new hose with clip to discharge pump. Clipped in new drain hose to the washer frame. Re-installed washer cover and re-clipped brackets. Re-plugged lid switch and re-installed the washer control box. Turned on the water and energized the washer. Ran a test load and checked for leaks.

Simply put the new one on. No tools required.

Tried to follow videos. Couldn't figure how to raise top. Laid machine on front used pliers to unclip bracket and clips holding hose. Took 10 minutes to work it this way.

The tough part was replacing the front cabinet.
I did consult the video for help on replacing the clutch spring.
Thank you for that bit.

I admit to taking too much apart, most of the cabinet back can be left alone.
Some of the plastic wire keepers/routers suffered, as well as the console hinges.

The newly reassembled washer works without a hitch, and truely it took me about 4 hours over several days to dissamble and reassemble.
It is louder in the audible range than before, but very serviceale for another 20 years, saints willing.

Removed housing, using pry bar lifted plate used screwdriver removed wear pads one at a time. inserted new ones and snapped into place. Did not have to remove tub. Be sure pry bar does not slip and you pinch your fingers. Machine works just fine know.

Went on-line for help.found parts select website.referred to your service videos.discovered solution to problem.bought proper part.arrived in excellent condition.watched another video for how to install the part.completed repair in about one hour.washer operating back to normal again. this site is a one stop answer/parts shop. thank you .

the tube when spinning the tub would shake so bad the washer would walk away from the wall but it will not happen anymore since I put the new spring on it runs great and this is not my first rodeo. Removed the outer part to timer controls then removed two screws then shell in front came off the body

went really good, received both parts in less than two days, great service! Video's on line were really helpful and made taking apart and putting back together easier, even though video's were on newer model machines. Would not hesitate to order parts from Part Select again.

First time .Replace the clutch .miss placed one of the retainer clip .found it after the replacement came .It was in the fold at the base of the machine.

Well, after resolving Part Select (PS) shipping issues (PS sent me two refrigerator glass shelves instead of a Tub Spring); And as it turns out they sent me the wrong part for the suspension pads, which I have returned for credit. It takes 3-4 weeks to obtain your credit BTW.

Well after removing the cabinet, agitator, wash basket, plastic tub, all 5 springs, & pump suction line, I was able to access the Tub wear pads and suspension pads. As it turns out the suspension pads looked good.
Thank God, as PS had sent wrong parts. I replaced the wear pads, the 5 springs, and reversed the disassembly process. Took about 6 hours.
But washer works fine now, still vibrates, but does not walk across floor any more.

Pull the washer out away from the wall and tip back.
I used a small metal ammo box to hold up the washer.
The bottom pump retainer is easy reach and remove with a flat screwdriver. I was able to pry off with my hand.
Replace retainer insert into slots on drive motor and twist.
I used a pair of Channellock pliers to lift retainer while pressing along the
side till it snaped into place.
Remove the support box and put washer back.
Then tip washer forward to reset self-leveling mechanism.