3CSP2760BN0 Whirlpool Dryer - Instructions

Removed the top panel of the dryer via a couple of screws from the rear. Remove the rear panel swing it open light a door to the right, minding the electrical connections. Removed the belt from the pulley, removed the Tri-ring from the shaft and slid the pulley off of the shaft. The shaft was slightly rusted so I used a steel brush and brake cleaner to clean it up, placed the new gasket, pulley, and tri-ring on, replaced the belt, and put the panels back into place. As the dryer is about 7 years old, also removed the front lower panel and cleaned out unit which had quite a bit of accumulated dust and glitter especially in the vent lines. (3 girls live here). Pretty easy, most screws remove with just the one tool.

After disassembling, I orderedparts.was told it could be the thermal fuse.found that the belt was broken.disassembly was simply removing screws, but as a novice, it was difficult to determine what to remove and how to remove only what was needed.after watching your video, it was much easier.replaced thermal fuse and belt.made sure to clean lint from motor and interior of dryer as well as vent lines and vent blower.the old machine works fine, until something else goes.

Open the top and replaced the switch bracket with the actuator lever then inserted new door catch.

replace the burnt fuse.

I followed the basic steps in the video for the dryer door switch replacement. My dryer is much older but everything in the video was basically the same. It was a very easy repair. I have kept this dryer running for 26 of the 27 years of our marriage.

UNPLUG UNIT FIRST!!! Removed back cover. Make sure to note not all screws hold the back cover by closely observing the screw. Take a picture of the belt routing before removing from the idler pulley. Use headlamp or flashlight to light up pulley area. Remove belt from idler pulley by pushing idler assembly towards the right. Use small screwdriver to remove the existing pulley by prying off the existing tri-ring from the back of the pulley. You may have to "feel" the ring since it in facing away from you. Once tri-ring is removed, slide off old pulley and gasket or old second tri-ring. Replace with gasket first, then pulley then tri-ring. Reroute belt. Use picture if needed. Replace back cover.

Tool of the back & cross brackets. I did not have to mass with electric panel. I did not have to remove the drum.

Removed the current (broken) block by unscrewing the screws at each end. I decided to re-use the wires / connectors in the dryer, though. The connector on the dryer is held in the block by a bent tab, about half way along the connectors length. I pushed this with a screwdriver and pulled the connectors off the current block. Sometimes I had to re-bend the tab prior to putting on the new block. Then I slid the connectors into the new block. To do this, first you put the captive nut into the slot, and then you put the metal end of the connector below the block, so the wire is around half-way down the block. Then slide the metal in, trying not to pull on the wire. Lastly I reattached the block to the machine using the two screws. Didn't need the terminal block screw kit, as these parts were in the block-term kit.

I'm a 66 year old lady with no repair experience at all!! I found the part I needed on Parts Select, which I ordered and received in less than 4 days. I watched the video that you've posted on your website which shows in great detail how to do this repair. It looked like a simple fix and it was!! I highly reccomend Parts Select!! Took my granddaughter(held flashlight) and myself less than 30 minutes to do the repair!!!

this belt is too thin for the capacity of this dryer.I had only removed the front panel,replaced the belt and immediately the dryer start.

Removed the old one installed the new one

Once I watched a YouTube video showing me how to do the job I ordered the part from you. Am so impressed with your fast shipping and best prices via the Internet. Thank you SO much! The water level switch was easy to install, it ws getting the cover on the washer back on that was hard for me since I am 68 yrs old and have a bad knee. Its why it took me two hours to do what most people could do in 20 minutes.

little more than vedio showed has a see thru door had to tke door off machine then was easy replacement and re install

I watched the online video first, which made the removal and installation fast and easy.

we received the two heating element wires in 3 days and connected the heating element with no problem works great.