36-3272-66-08 Tappan Range - Instructions

Really easy to do, did not have to bring stove out from the wall! Turn power off to the stove. Remove the lower drawer. Remove the oven rakes. With a slotted screwdriver remove two screws in back of bottom oven cover, use 1/4 inch socket to remove two screws in front. Remove bottom oven cover. You can then see the part to be removed which has two wires going into it, the unit looks identical to the new part which heats up and lights the gas grill for the oven. I cut the two wires from the old part, remember which is the upper and lower; remove two screws holding onto part. Wire new part remembering top and bottom. Push extra wire down into bottom drawer and then mount new part with two screws. Turn power back on and try oven. Lite right away for me so I knew I had replaced the bad part. Reassemble and Enjoy!!

This was very easy. Just remove the bottom of the oven by removing the two screw in the back. Then remove the baffle from under that and you of will see the ingniter. The one wire will reach the gas valve, just splce the other. 6 screws is all it takes. Turned it on worked perfectly.

1- put in new thermostat 2- put in new gas valve 3- put in oven igniter ....3rd time a charm. Now I have all new oven parts! My husband installed and said it was pretty easy, have to take the oven door off and inside bottom out.

remove screw, remove burner, install new burner and screw

Removed oven door, removed oven floor. Unscrewed skirt with attached igniter and gas tube. Two nut screws hold igniter to burner. Remove old igniter and replace with new, reattach two wires with supplied wire nuts. Replace oven floor and door. Oven lit right up, pizza anyone?

AS YOU DESCRIBED IN YOUR YOU-TUBE VIDEO, THE OVEN IGNITER WOULD GLOW BUT THE OVEN WOULD NOT LIGHT. YOU EXPLAINED THAT THE PROBLEM COULD STILL BE THE IGNITER AND SO I ORDERED A NEW IGNITER AND THEN WATCHED YOUR VIDEO ON HOW TO ACCESS AND REPLACE THE NEW IGNITER AND THAT FIXED THE PROBLEM. I ONLY HAD TO CUT THE OLD WIRES ON THE OLD IGNITER AND MATCH WIRES WITH THE NEW IGNITER USING THE CERAMIC WIRE NUTS SUPPLIED, AND I WAS BACK COOKING AGIN. THANKS.

CUT THE WIRES ON OLD IGNITER AND WIRE NUT THE WIRES OF THE NEW IGNITER TO WHERE I CUT THE OLD ONE OFF.

No Problem, couldn't find them at any local repair facility so I looked on line and found them here, ordered 4 drip pans and the exact replacements came within a few days.

Thank you, Thank you and thank you!!! I couldn't be happier and I save over $200 in repair. My repair was very easy after watching the video. I cut off the wire and ensure that the new one are attached into place. Placed all parts back and boom, the oven starts working a new.

First thing is I looked for videos on how to replace oven igniter to get an idea. Unplug AC cord and turn off gas valve.On my model I was not able to figure out how to remove oven door. You can still work around it without removing. Inside the oven, remove bottom cover. Remove 2 screws located in rear corners. After removing oven bottom cover, next is a burner cover. Remove 2 screws located toward front of oven using a nutdriver or socket. After removing burner cover , you will find oven igniter. Now remove bottom drawer. This is why its a bit difficult for others. Igniter has 2 leads. Laying down on the floor and reaching in to follow-identify where the 2 leads go to. Using same nutdriver or socket remove 2 screws that hold up the igniter. I cut the leads from the base of the old igniter so you will have some slack to work on when you reconnect the wires underneath. Install new igniter, run leads same way.Strip back about 3/8 in. wire, twist leads to proper wires and twist on ceramic wire cap that is provided. Make sure no bare wires are exposed! Now you can test.

pulled drawer out and took old igniter off and replaced it

took of bottom pan and pan above the gas flame off and the igniter off , cut the two wires. replaced the igniter hooked the wires togther, replaced both pans. turned the oven on and it lite

remove bottom pan, remove gas second cover, loosen nuts on ignitor, cut wires near the ignitor end for extra slack, connect new wire of ignitor, screw on wire caps, reattach ignitor, replace covers and finished. Very easy repair.

Removed 4 burner knobs. Unscrewed 6 phillips head screws on manifold.Pulled back manifold enough to remove switch. Removed the Two wires from switch and hooked them up to the new switch. Slid new switch on to shaft and in reverse order, reasembled manifold, screws and knobs.

had to remove burner bolts holding igniter were stripped cut two wires replaced igniter using two self tapping screws put wires together using wirenuts Honey making cookies right now thanks already told friends about you