3201 - Instructions

The oven had been working intermittently for a while and after repeated threats of starvation from my spouse I finally took a look even though it was summer and the grill was working fine. The Igniter would glow red when the oven was turned on but the gas would not flow to it no matter what the temperature setting. I searched online and found this site that explained it was possible for the igniter to glow but if it was not drawing the correct amperage (because its resistance was too high) then the main brain would not allow the gas valve to open. So I took a look at the broiler and it had the same igniter. I measure the resistance of both of them and the oven igniters resistance was higher (don't rememeber the reading) then I moved the Igniter from the broiler to the oven and the oven worked from there it was just a matter of ordering the part. End of story except for I am still doing all the cooking on the barbecue outside.

I have a fridge in my garage. I have found that a glass of ice water or a cold drink outside is very important to me. When I discovered melting ice dripping onto the garage floor I was very upset. I spun the fridge and found that the compressor and fan weren't starting. I got out my multi-meter and discovered that power was not making it to these components. I did some research and found the wiring diagram online. There really isn't too much going on with a fridge and the most likely candidate seemed to be the run capacitor. I ordered the part, replaced it in a few minutes and the fridge began working again.

In most cases if your oven won't light or takes a long time to light you may have a bad igniter even if it glows. To check the igniter use a voltmeter to check for 120 A/C volts going to the igniter and3.5 A/C volts going between the ingniter and the gas valve. My bad ingniter glowed but had only only 3.0 A/C volts going to the gas valve for the oven. The new igniter took only 45 minutes to install and supply's 3.6 A/C volts to the gas valve and the oven works fine.

My son replaced the broiler igniter this spring, so I had a clue as to what was required. This was even easier and since I had back surgery recently & my husband was out of town that was a giant plus!

I unplugged the oven, removed the oven door, found the release latch and removed the oven floor. I then removed the 2 screws that held the igniter in place (I received this stove used and the igniter had evidently been replaced before as it was the same shorter version included in the kit). I pulled the igniter out then removed some insulation and tugged the connector out of the oven floor. I disconnected the igniter and plugged the new one in. I then replaced the connector in the floor, attached the igniter with the screws, replaced the insulation and did a test run (plugged in the oven & turned it on). That was successful so I put the floor back in and put the door back on.
Ta-Dah!

This repair project was too easy!...and cheap. Sears quoted the price of the igniter at $280 plus the service call and the item cost $41 on PartSelect. The part was received the next day after the order was placed...WOW! So easy, turn off the power to the oven, open the oven door, remove the oven racks and lift the bottom pan of the oven up from the back and set it aside. There you see the flat type igniter in plain view at the back of the oven. Remove two screws with nuts using a nut driver (I had trouble because the screws were corroded and I had to use some, um, force to get them out and swore a little too). Once the screws were out, pull the igniter elecrtic wires and connector from the entrance hole in the back after moving a little insulation out of the way. Release the connector plug and unplug the old igniter and simply plug in the new one. Find new screws and reinstall in reverse order. Be sure to push the connector and wiring back into the hole and cover with the insulation. Very easy job that anyone could do.

unplugged refrigerator. removed light bulb from old socket. unsnapped old light socket and pulled it out just enough to diconnect the electrical plug that plugs into the socket . discarded the old socket and plugged in new socket. snapped in new socket into refrigerator. i watched how to do this simple procedure on you tube and decided to do it myself. easy easy easy

I removed the rear access panel on the oven in order to get to the igniter wires. While testing the output voltage of the old igniter when on, I found that it was producing less than 3 volts ac. This was my clue that although the igniter glowed, it was going bad and needed to be replaced. I unpluged the oven, shut off the gas feed to the oven then removed the oven bottom pan (pull two push pins back, lift up and out) and removed the burner baffle wing nut with baffle. This gave easy access to the igniter and it's two mounting screws which i removed using a phillips screw driver. I unpluged the old igniter from the connector, pluged in the new one after routing it through the access hole from inside the oven to the back of the oven where the connector is located.
Mounted the new igniter, replaced the burner baffle, baffle nut, oven bottom, rear access panel cover, checked and turned on the gas, plugged the oven back in and sure enough it fired up right away. if you check the system of how your oven works and find the problem, it's easy to fix it yourself and save serious money...and look like a hero to the rest of the family.

Removed back panel. Opened cover to relay attached to the compressor and pulled off replacing with new relay. No problem.

Better than paying $250 for someone else to do it.

removed old clips and remaining parts of old seal...new part already had clips attached, so just snapped them into holes in oven door.

This oven was located in a rental house I own.

I first removed the metal plate that covers the burners at the bottom of the oven. No tools required for this step.

Next I turned the oven to 300 degrees, waited 30 seconds and noticed that the igniter was glowing brightly, but the burners did not light.

I next turned the oven controls off, pulled the plug, and set to work removing the 2 screws holding a plate to the back oven wall and the 2 screws holding the igniter to the burner. These last 2 screws had corrosion on them and I needed to use vise-grips to get a firm hold on them. During reassembly these screws no longer held firmly because the hole they threaded into was enlarged during disassembly.

With the screws loose I pulled the igniter and fished the wires connected to it through the opening until I saw the connector. I then pulled the stove out of its opening and saw that there was a easily removable metal cover over the wires, and I took it off.

The new igniter came with an incompatible plug, so I cut off the connector on the stove wiring and on the new igniter and used wire nuts to make the new connections. I kept the orientation of the old and new plugs the same way in case the wiring mattered, but that was just being safe. I don't know if the igniter cares which of its wires go to which wire on the stove.

I reinstalled the screws holding the igniter, and shoved short sections of the supplied wiring into the screw holes so that the screws would hold more tightly. I shoved the supplied insulation into the opening that the wires passed through, and reattached the cover at the back of the stove.

I shoved the stove back into its opening, turned the oven on and it lit within 15 seconds.

I was very happy with the result, and the product I ordered arrived on time, well packaged and I'm a very happy customer.

First I opened the door to the oven. Then I opened the box that the part came in. (knife) I then slid the oven rack out of the box and unwrapped the plastic, being careful not to bend or scratch the new rack. Now, this is the tricky part... I had to move the existing rack down one space to make room for the new one. Then carefully slid the new rack in, tipping it slightly and sliding it in. LOL

i need to replace the lower oven igniter about 2-3 years
unplug the oven
open the oven door half way then slide the door up
take out both racks
push the bottom pan away from you and lift up
one screw holds the igniter on
pull the wire out until you get to the electrical plug
disconnect

I am a retired lp Gas service person so this was quite
simple for me. Replaced the oven Igniter. What amazed me I placed my order and had the Igniter less than 24 hours. thank you so much for the quick service.

Found burned Defrost timer contacts.

first of all i have one advantage even though i am 70 yrs old i had a appliance shop for sears in the 60s and 70s and have not forgotten to much of the basics i am still in the security business and up on electronics. last time i had the company repair the oven , 70 dollars for the part 75 dollars for the svs call. (first igniter was on full warranty) well this time i decided to look for trhe part myself, i just went on line typed in oven repair parts and eventually all these sites came up. yours was the most professional looking and i took a chance. guess what everything you promised you delivered. price quality USA made parts and delivered in three days . opened package went to work less than fifteen minutes back in business.
will sure use you again if the need arises thank you