2748 Husqvarna - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Wheel bushings were bad
Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat other side.
Parts Used:
-
Anthony from OLIVEHILL, TN
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
12 of 20 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken weld on right axle
Removed wheel (used strong magnet to catch the keeper)
Removed axle assembly from its mounting tube
(used strong magnet again to prevent keeper lose)
Installed replacement axle (again with the magnet)
Lubricated with 90 SAE
Re-installed the wheel (used magnet again to hold the keeper.
Mowed the lawn.
Removed axle assembly from its mounting tube
(used strong magnet again to prevent keeper lose)
Installed replacement axle (again with the magnet)
Lubricated with 90 SAE
Re-installed the wheel (used magnet again to hold the keeper.
Mowed the lawn.
Parts Used:
-
walter from EDINBURG, VA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Take the wheel off. Place the key in the slot. Put the wheel back on.
-
Gary from PILESGROVE, NJ
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
3 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer runs no heat
Disassemble dryer. Replaced element assembly. Re assembled dryer. Unit runs and heats.
Parts Used:
-
Russell from MACON, GA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lound deck noise when mower put into motion
Parked mower on level concrete drive, laid on cardboard. Lowered mower deck all the way. Sparayed some WD40 on nut/bolt on top of old pulley. Since it is a carriage type bolt, placed 5/8" boxed end wrench over self locking nut on top of old pulley. Using some force from 3lb mallet to break nut free (hitting against wrench body), the nut came off easy as did broken pulley/bearing inside. Installed new pulley assembly, re-tightened nut on bolt. Checked after first mowing just to be certain pulley was in place and locking nut tight.
Parts Used:
-
Steven from Hickory, NC
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set, Wrench set
4 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken v-belt for drive
I returned the belt because it was the wrong part. Ordered the correct belt from another source. After that the replacement went well and I crossed off Parts Select from my list.
Parts Used:
-
Paul from ROCKTON, IL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Wrench set
2 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Front wheels, too much end play
-
Frederick from BINGHAMTON, NY
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
7 of 28 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!