25348022893 Kenmore Refrigerator - Instructions

I'm too young to die so I unpluged the refriderator first. The cold control is mounted in a plastic housing at the top of the freezer compartment that is held in place by two screws on the back side. I removed them with a nutdriver. Pull off the knob and use a screwdriver to release the control from it's bracket and pull off the 3 wires noteing where they go. Slide the sensing element out and remove the plastic sleeve. Stragihten the sensing element on the new control and slide on the plastic sleve. Slide the sensing element in place, push the wires onto the terminals and snap the control into the bracket. Re-install the two screws and the control knob. Plug it in and you're done. It took longer to write this than to replace the control.

My freezer was frozen but my refrigerated side was not cooling, the temp was actually around 60-degrees. After inspecting i noticed no air was flowing through the vent from freezer side to fridge side. I removed everything from freezer and took the back wall panel off inside freezer section and immedietely noticed alot of ice on coils etc. After researching i found the defrost timer was not working and thus allowing frost and ice to build up on coils and block air flow. My defrost timer was located on the front bottom left behind kick panel, using a phillips screwdriver i removed 2 screws and then disconnected wire harness to the defrost timer. Then i inserted new defrost timer and connected wire harness and then put the 2 screws back in. My fridge is now working great and the ice build-up is gone and i am getting good air flow .. temps on fridge side are now between 32-34degrees. This was an easy project and saved me alot of money doing myself

i removed the 4 screws holding cover. removed two screws holding timer. unplugged timer. plugged in new one. reassembled.

First, unplug the refrigerator since you're working with live wires.

Remove the 4 Philips sheet metal screws holding the plastic housing that holds the temperature control to the top of the refrigerator compartment. Pull the housing down then out since there is a tube on the housing where the water flows out the back of the refrigerator during the defrost cycle.

Remove the 2 Philips screws holding the defrost timer on the plastic housing. Pull the connectors off the old timer and attach them in exactly the same positions on the new defrost timer.

Attach the new defrost timer to the plastic housing with the 2 screws.

Reinstall the plastic housing, making sure the water tube is inserted into the back of the refrigerator wall.

Plug the refrigerator back in and you're done.

Used exploded parts view to locate part. Removed old part and replaced with new defrost timer. Piece of cake.

- Unsnapped old light socket from top of Frig
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.

Popped off the front plastic cover on the bottom of the fridge, under the doors. Two screws held the defrost timer on under the front side of fridge (below freezer door). You can't really see the timer except for the adjustment knob that is accessible through a hole. Once the screws are removed, disconnect the wire plug and remove and replaced unit. Works fine ever since.

Super easy, I removed the drawer fronts off the broken drawers by sliding them off and simply slid the existing drawer front onto the new replacement drawers. Slid the new drawers into place. New drawers fit perfectly.

Unplug fan and remove 3 bolts. I had to bend the fan frame in order to remove fan. Change fan blade and reverse procedure. Fridge is fixed nice and cold

Removed the old fan--three small nuts and snap off connection. Ordered part and received the next day. Your company is great!!

The end caps worked perfectly for both the Frigidaire and Westinghouse fridges. Just pulled out the old end caps and then literally just pushed in the new ones (remember to attach the shelf bar before attaching the second end cap!). The pieces arrived quicker than expected. Thanks Partselect!

it was pretty straight forward, pulled the old drawer out , emptied it out of all the food of course then i removed the front clear panel using a screw driver to gently pry off that part, the front then just slides and snaps on to the new part really easy . slide it back in and hopefully it should last another 10 years.

I removed the front cover from the original drawer and slid it onto the new one from PartSelect. Perfect fit. I recieved my part in only two days with regular ground shipping and I am completely satisfied with the part and service.

Twisted replacement bulb into place easily. Let there be light!

Had to pry off front glass of drawer with screwdriver.Very east install. The shipping for this part was the fastest I have ever recieved.I called at about 2:00pm and had the part the next day at 2:00pm..incredible service