Models > 21468

21468 Toro Lawn Mower - Overview

Models starting with 21468

Click on the best match to narrow your results.

Exact Part matches for your search term

[Viewing 2 of 2]
Valve-intake-1/32 oversize-inc 9 – Part Number: 21468
Valve-intake-1/32 oversize-inc 9
This part number matches the current model number 21468
PartSelect #: PS12399201
Manufacturer #: 21468
  No Longer Available
VALVE LEVER BRACKET – Part Number: 21468
VALVE LEVER BRACKET
This part number matches the current model number 21468
PartSelect #: PS16564007
Manufacturer #: 21468
$8.01
  Special Order
Keep searches simple, eg. "belt" or "pump".
Washer-Stepped – Part Number: 614426
Washer-Stepped
★★★★★
★★★★★
(1)
PartSelect #: PS9048394
Manufacturer #: 614426
The Stepped Washer is used to secure the wheels onto the shaft of a push mower. It attaches to the wheel axle. If broken due to wear/fatigue, the wheel will come off and the part should be replaced. I...
$3.99
  In Stock
Baffle-Front – Part Number: 114-7963-01
Baffle-Front
PartSelect #: PS8845729
Manufacturer #: 114-7963-01
$40.23
  In Stock
Bearing-Ball – Part Number: 104-8699
Bearing-Ball
PartSelect #: PS8824569
Manufacturer #: 104-8699
$4.99
  In Stock
Screw-Hwh – Part Number: 46-8091
Screw-Hwh
PartSelect #: PS8974798
Manufacturer #: 46-8091
$4.99
  In Stock
Gear-Pinion, 15T – Part Number: 131-5399
Gear-Pinion, 15T
PartSelect #: PS11804780
Manufacturer #: 131-5399
$4.99
  In Stock
Nut-Lock, Ni – Part Number: 3296-29
Nut-Lock, Ni
PartSelect #: PS9276436
Manufacturer #: 3296-29
The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is use...
$3.99
  In Stock
Ring-Retaining – Part Number: 32151-61
Ring-Retaining
PartSelect #: PS8950132
Manufacturer #: 32151-61
This metal retaining ring, otherwise known as a snap ring, holds parts in place in your lawn equipment, such as blades, shafts, pulleys, or other rotating components, to prevent them from sliding off ...
$3.99
  In Stock
Support-Blade – Part Number: 108-3766-03
Support-Blade
PartSelect #: PS9257416
Manufacturer #: 108-3766-03
The Blade Support is a 6-x-3-inch Black, metal part used to support the blade. It's rated as "Easy" to install by customers. It must be torqued to manufacturer specifications which will require a sock...
$11.20
  In Stock
Washer-Thrust – Part Number: 110-7191
Washer-Thrust
PartSelect #: PS8838552
Manufacturer #: 110-7191
$3.99
  In Stock
Guide-Cable – Part Number: 114-7988
Guide-Cable
★★★★★
★★★★★
(1)
PartSelect #: PS8845311
Manufacturer #: 114-7988
$3.99
  In Stock
Bushing-Sleeve – Part Number: 108-9782
Bushing-Sleeve
PartSelect #: PS8833696
Manufacturer #: 108-9782
$3.99
  In Stock
Bolt-Blade – Part Number: 125-2466
Bolt-Blade
PartSelect #: PS9885938
Manufacturer #: 125-2466
$3.99
  In Stock
View More
Back to Top
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Wheel height adjuster lever (spring steel) cracked / split in two.
Tip mower onto side, raising side to be repaired. Empty gas tank if possible or use rags to prevent gasoline drips onto clean surfaces.

Remove wheel using a 1/2" socket.
Remove wheel height assembly with 1/2" socket and open end wrench to hold nut below the deck.
Position new spring arm over the slot on wheel height assembly plate. Check opposite side to verify correct orientation if needed.
Remove plastic cover from old lever using a small flat blade screwdriver. Slip onto new lever.
Replace wheel height assembly.
Replace wheel.
Read less
Parts Used:
Arm-Spring
  • Ray from YARDLEY, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set, Wrench set
3 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
View More
Back to Top