20239 Jenn-Air Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
circuit breaker blew
I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.
Parts Used:
-
Richard from Sarasota, FL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The burner didn't heat to full temperature.
First turn off the power to the stove/oven. Next I removed the 4 screws located on the bottom surface of the control panel. You need to open the oven door to see/access them. The control panel can then be removed by rotating the bottom outward which allows the flange on the top to disengage. Next remove the two screws that hold the switch to the control panel. Note which wire goes to which spade connector. A quick photo can help. Undo the wires. Remove the old switch. Reinstall the wires. Mount the new switch to the control panel. Mount the control panel back into the stove/oven. Turn on the power and test. The burner now works as new!
Parts Used:
-
Stephen from Grants Pass, OR
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
glass in oven door was broken
We took the door off, you have to be careful of the hinges popping back. We put small screwdrivers on each side and held the hinges out, this made the door easy to just stand up and slide back on the hinges. The glass replacement was simple just a few screws. We spent $127.00 on the part and shipping and a new wall oven would have cost us $1500.00. Thanks for making this part available.
Parts Used:
-
Vonnie from Indian Rocks Beach, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
grill would not get hot enough
I have a newer jenn air with the 3 prong elements. The original element was 3 prong 1900W only using one of the controls. Since the stove socket would accommodate 4 prongs I looked up the part for the older stoves (PS2357533)which had 2 elemants using both controls. The element plugged right in and I now have high heat like on my older models and it now grills like it should instead of just heating the stuff up. Highly recommended. One caution you will need a metal piece to support the element since the newer stoves do not use the metal bricketts with supports.
Parts Used:
-
Paul from Berlin, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Parts Used:
-
Grant from Alexandria, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Replaced worn seal
Remove the door. Place small screwdriver in each door arm to prevent extraction. Remove approx 20 screws. Remove the seal. Replace the new seal. you will need help in holding the seal in place until you car install at least two screws. Very straight forward. Took 20 minutes. Even a cave man can do it.
Parts Used:
-
Horace from Las Vegas, NV
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Burner stays hot
First turn off breaker, then take screws out switch assembly,take oid switch out, put new switch on,turn power on.
Parts Used:
-
Gregory from snellville, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
very old grease filter.
Very easy to replace the filter, nothing to it, take out the old filter and put in the new filter.
Parts Used:
-
Eliane from Potomac Falls, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Simply replace the grease filter
Thanks for carrying this part for my old stove. And thanks for the great service.
Parts Used:
-
MaryAnn from Scituate, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Door seal was worn out/burned /leaking heat
Took the oven door off hinge. Took door apart pulled off old seal from inside of the inside panel of door. Replaced with new seal.
Parts Used:
-
Christopher from Toledo, OH
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Burner would stay on high, on all settings.
In response to your question.......everything went perfectly!! The reason?? I read the directions that were very easy to follow. It was a quick, easy repair, and the stove burner is working like new.
Thank you for your help!!
Bob
Thank you for your help!!
Bob
Parts Used:
-
Robert from Attleboro, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Burner always on high, no temp. adjustment.
Removed 4 screws, tilted cover up and lifted out, removed wires from switch, removed 2 screws holding switch, lifted switch out. Replaced with new switch, connected wires, secured cover with the 4 screws. It worked!
Parts Used:
-
Woody from New Castle, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
burner cartridge terminal broke due to electrical shock. circuit shortage caused the problem.
dissembled the burner, remove the broken blocpk and bad spade.rewiered and assembled the burner.
Parts Used:
-
Ge from Solon, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Frozen screws
Followed instructions. Two screws frozen. Unable to loosen. Forced to grind heads off and replace with new screws.
Parts Used:
-
Jack from Lake Wells, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Left Rear Burner would not work
Shut off breaker, removed the top by unscrewing the retaining screws and removing all knobs and grommets. Removed control from top panel by unscrewing, removed 5 wires and placed on new control. I then remounted the control, placed the top in its well, fastened. Replaced the retaining screws in the hold down strip and replaced grommets and knobs. Returned power to panel by turning the breaker on and tested. Used later that evening to grill 2 panini.
Parts Used:
-
Sharyl K from Nampa, ID
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!