1ET25DKXGW00 Whirlpool Refrigerator - Instructions

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

real easy to install and it works fine. However, the problem was more complicated. The circuitry on the ice maker on the back side of where the gear that rotates the harvesting fingers had places that were not making contact. I took a dart, yes, a dart from my dartboard and pressed the copper contacts down so they made contact and all appears to be well. Well at least until tomorrow. yikes.

Thanks to some reviews we found online about replacing gaskets, ours went very smoothly. One person said to soak the gasket in hot water, which we did til it was very soft. Installed like a breeze. Then, the same person said to tape the door closed after installation, we did that too. The gasket looks like it was professionally installed and we have never done it before. Thanks!

I followed instructions, both supplied with gasket, and some I found on-line. Pretty easy - loosen screws holding existing gasket, remove existing gasket, install new one, tighten screws. [TIP - I didn't soak new gasket in hot water before installing - definitely do this to get rid of the "wrinkles" caused by shipping. Throw it in a tub, and let it soak.] The problems I had to iron out were AFTER I installed new gasket. Door alignment shifted, so I loosened all gasket screws, realigned, and then tightened. Then door was not closing (it had dropped for some reason at the handle side), so I had to loosen hinge bolts, push up door, and re-tighten. I had to do this 3 times before door closed right. I also had to heat two sections of the new gasket with blow dryer to smooth gasket. After about two days, the gasket was sealing perfectly. No condensation in fridge, no leaking out bottom. I estimate by putting in a $100 gasket, I saved over $1,500 because my wife was ready to get brand new fridge. Good luck, and be patient if door needs to be realigned. Also - gasket may still have small gaps even after you install and heat it - give it a few days to conform to fridge before trying heat again.

be sure the power cable is NOT plugged into an electrical outlet - removed the cover on the bottom rear of the refrigerator - using a flat blade screw driver pry the cover off the side of the compressor - remove the old relay - remove the wires from the old relay and install them on the new relay in the same location - install the new relay on the compressor connections - snap the cover back on the compressor - replace the cover - power the refrigerator on - the compressor should start and run normally

tested that water got to inlet valve, but not past it. the rod inside the pump was separated from the plunger. i ordered part. i was quite impressed that i got part within two days. replaced valve. ice maker works.

I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

Went online and located the right part numbers. When delivery happened I put it together and all is fine now.

replaced thermostat