Models
>
13BD608G101
13BD608G101 (( 1H019H - 1H310H)) Cub Cadet Lawn Mower - Overview
Sections of the 13BD608G101
[Viewing 1 of 1]Keep searches simple, eg. "belt" or "pump".
Rod-Push (Steel)
PartSelect #: PS9062983
Manufacturer #: 690981
This is a replacement steel push rod for your lawn tractor engine. The engine will have two push rods; one made of steel, and one made of aluminum. This part is made of steel and is approximately 6 in...
$6.89
On Order
Seal--Oil (PTO Side)
PartSelect #: PS9151828
Manufacturer #: 795387
This OEM Seal-Oil (PTO Side), also called the Oil Seal, is a Black, Nitrile Rubber, 2/14 O.D., individually sold part which is installed using a Seal Puller. Customers rate the installation difficulty...
$7.88
In Stock
Gasket-CylinderHead
PartSelect #: PS9067184
Manufacturer #: 693997
This is a replacement cylinder head gasket for your small engine. The gasket is approximately 5 inches in length and 5 inches in width at its longest and widest points. The gasket creates a seal, and ...
$26.91
In Stock
Gasket--Exhaust
PartSelect #: PS9294808
Manufacturer #: 692236
This OEM exhaust gasket in lawn and garden equipment creates a seal between the engine block and the muffler or exhaust pipe so that exhaust gases do not leak. This is 3.30cm in diameter and 6.35cm in...
$5.71
In Stock
Seal-O Ring
PartSelect #: PS9294749
Manufacturer #: 691917
The Seal-O Ring, also known as the gasket, is red in color, made of rubber, and is an OEM part that requires some skill to replace. This part is designed to create a seal between the carburator and ma...
$4.99
In Stock
Cylinder Head
PartSelect #: PS9152257
Manufacturer #: 796231
This is a replacement cylinder head kit for your small engine. It contains everything you will need to replace a damaged cylinder head. This is a 12-piece kit that is sold as a unit. This is an OEM pa...
$181.00
On Order
Crankcase Gasket With Bolts
PartSelect #: PS11829358
Manufacturer #: 594195
This genuine crankcase gasket is used on small lawn and garden engines. Its purpose is to make an air tight seal so that no air/oil leakage occurs. Over time this gasket will deteriorate and will need...
$37.66
In Stock
Questions And Answers for 13BD608G101
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 13BD608G101
[Viewing 1 of 1]Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Engine quit due to valve guide sliding out causing rocker arm to be immovable resulting in bent push rods.
Clean engine with a Gunk type product. Remove valve cover. Loosen bolts and remove old cylinder head. One bolt is located inside valve cover area. Remove old gasket and inspect and clean that surface. Attach new head with new gasket using existing bolts. Torque to 18'#s with a cross type pattern. Attach new rocker arms and push rods. Set
... Read more
valve clearance to .004 - .006. Attach valve cover with gasket. Check oil level. Start and let it warm up. Let cool remove cover then check valve clearance again. Replace cover.
Read less
Parts Used:
-
D from HUNTSVILLE, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Socket set
11 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
governor not working
Had to pull the engine off the rider mower. Drained the oil took shield off the flywheel. Set it upside down on a 5 gal bucket. Took a 7/16 hand wrench to remove governor lever from bottom of engine. Left it in its location. Pulled 10 1/2 " bolts. Split engine case. Found the old governor had broke into pieces. Had to use a magnet t
... Read more
o remove all the pieces. Removed the small clip and removed gear. Lubed shaft slid new on put new clip on. Lined governor weights with center piece tapped it in place very lightly. Cleaned gasket flanges pulled the shaft seal. Used the old seal as a seal driver. When putting the cover back on make sure the seal dont roll out. Take a mini screwdriver and tuck it in around shaft. Put bolts back in and tighten like instructions
Read less
Parts Used:
-
rodney from MUSCATINE, IA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Screw drivers, Socket set
12 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
i NEEDED A DRIVE BELT FOR MY RIDING MOWER
1) DON'T ORDER FROM THESE IDIOTS.
2) THEY SENT THE WRONG BELT
3) THEY HAVE A CUSTOMER -NO- SERVICE NUMBER.
4) CAN'T GET A GOODS RETURN ONLINE
2) THEY SENT THE WRONG BELT
3) THEY HAVE A CUSTOMER -NO- SERVICE NUMBER.
4) CAN'T GET A GOODS RETURN ONLINE
Parts Used:
-
TERRY from OAK CREEK, WI
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
6 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!