Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 11010202001 > Instructions

11010202001 Kenmore Washer - Instructions

All installation instructions for 11010202001 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11010202001
1,381-1,395 of 1,804
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Not spinning fast enough to take out water in spin cycle's

  • Customer: Jason from Appleton, WI
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
I simply watched the video that was on YouTube for this site. It was dead on with my washer and super easy to do. The step by step was just awesome and easy to follow. The repair took just over an hour and I even cleaned the entire inside of this 12 year old washer which was pretty cruddy. The washer now spins great and works like new again. All for about $50. Thanks.

Wouldn't spin on the spin cycle

  • Customer: Leon from Rockland, MA
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
A word to the wise watch the repair video first guys and save an hour or 2 of aggrivation. I saved a couple hundred bucks instead of having the repair guys do it. It was easier than I thought. Machine runs like new again. Thanks Partselect. L.A.B. Rocland, Mass.

Water leaking from under the front of the washer

  • Customer: Nathan from Lebanon, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Disconnect washer from all connections and slide away from the wall far enough to give clearance where you can tilt the washer and lay on it's back. Remove old pump and replace with new pump, then reconnect washer to wall connections.

Our washer was pumping but not spinning

  • Customer: Lauren from Woodstock, GA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The repair was surprisingly simple. We followed the video and it was a simple fix :)

leaked water on the floor, out of balance in spin cycle

  • Customer: Edward from Falls, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
1)removed philips screws at sides of control panel 2)lifted up and flipped panel over backward 3) disconnected wiring harness to lid switch 4)removed two snap off connectors at top back of washer with screwdriver 5)remove top lid and side housing as one unit 6) removed removed top lid and side housing and core of washer to driveway 7) ran over unit with an Ingersol Rand 84" smooth drum vibrating roller

Top agitator would not turn during the wash cycle, and I could spin it freely in both directions while the washer was not in use.

  • Customer: Richard from Wareham, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Popped off the fabric softener dispenser with a medium flat tip screwdriver. Removed the agitator screw with a 7/16 socket. Pulled out the agitator assembly. Pulled out the agitator cam assembly. Removed the 4 worn directional cogs/replaced with new ones. Reassembled in reverse order.

Top portion of agitator would not agitate

  • Customer: James from Long Beach, MS
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed the agitator with a straight blade screw driver and then removed by hand the inner cap. Used a 7/16 socket with a long extension and ratchet and removed the agitator bolt. Once the bolt was removed I pulled agitator cam the contains the agitator dogs out of the Mover, Agitator. I replaced the worn agitator dogs with new ones and replaced everything and it worked fine. I did mark with a red Sharpie the direction the dogs were before removing them so I would replace them in the right direction. Very simple job that took less than 15 mins.

Leaky Pump

  • Customer: william from independence, MO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Pulled the machine away from the wall about 18 inches. Tip the washer back until resting stably against the wall. Used plies to remove two spring hose clamps. Use the screw driver to remove spring clips. Pulled old pump off and placed new pump on. Replace spring clips and hoses with clamps, and lowered the washer. Done!

would not spin or take off on spin slowly

  • Customer: Rod from Huron, SD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
the video pretty much told the whole story except I forgot to put the plastic collar piece on the new clutch when I put it back together so I got to do it twice. second time went even easier. Thanks for the video,it was great.

agitator wouldnt move

  • Customer: robert from Roanoke, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Well i'm an auto technician by trade so I just jumped right in without reading or watching anything, but I saw the video and in the days waiting for the part to show up I watched it. I would recommend everyone to watch the video because it is simpler than I made it.Easy repair any mechanical skills at all and you shouldnt ave any trouble.

grinding noise wouldnt spin

  • Customer: Johnathan from Mountain Home, ID
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I have never fixed a washer, but this website made it very easy. I watched the video so there were no surprises. I unpluged the machine and disconnected the water lines and removed the two back screws. The control panel and shell came of very easy, i then tipped the washer on to its backand removed the clamps holding the motor. The motor came out very easy and the coupler was a cinch to put in. After that I reversed the process and then the wife was happy she got her washer back, Iwas happy too because I didnt have to buy a new one.

Agitator did not work right.

  • Customer: Ernest from Randolph, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
The installation of the new parts was easy to put in. No problem after I figured out how to do it. The parts came really fast and we were very happy with the service.

washer would not agitate or spin, even after replacing coupler

  • Customer: GEORGE from GERMANTOWN, KY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Found input to gearcase deformed, so new coupler slipped under load. Replaced gearbox. All function restored, but machine banged harshly during spin. Discovered that "skid plate" had shifted during gearbox replacement. Remounted skid plate carefully with pry bar, correcting vibration.

water leak

  • Customer: KYLE from MT JULIET, TN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
replaced water pump

No spin cycle

  • Customer: Stephanie from Frederick, MD
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I pulled up PartSelect, compared their advice with my problem, ordered a direct drive motor coupling for my particular model, received the delivery, and called a friend who's good at home repairs and who happens to be dating my sister. He was delighted to comply with our request (her clothes get laundered here) and he had no problem with either the repair itself or the part we ordered. Replaced the hoses, too. He said the new part had been improved over the old one, but everything fit together just like it should. Then I washed her work jeans. Success! I know this isn't what you're asking, but I was so pleased to have the correct part ready to go so he didn't have to mess around. It wouldn't have taken the afternoon, but I had to clean everything that had accumulated debris in 10 years of use as he went.
All Instructions for the 11010202001
1,381-1,395 of 1,804