110.6095299 Kenmore Dryer Parts and Repair Help
Models > 110.6095299

110.6095299 Kenmore Dryer - Overview

Models starting with 110.6095299

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
(76)
PartSelect #:PS334230
Manufacturer #:279570
This is a door catch kit, and it is designed for use with your dryer. On your appliance you will find both a strike and a catch. These two parts work together to keep your dryer do...
$4.92
In Stock
(66)
PartSelect #:PS1491676
Manufacturer #:W10120998
The filter collects lint during the drying cycle. This filter is 12 1/2 inches wide and 10 1/2 inches deep. Replacing the lint filter is an easy repair which requires no tools. Whe...
$45.96
In Stock
(89)
PartSelect #:PS11741416
Manufacturer #:WP3387747
This is a replacement heating element for your dryer. Its voltage is 240V/5200W and has 5/16" terminals. If your dryer is not heating up, the element may need replacing. You can te...
$75.33
In Stock
(59)
PartSelect #:PS334244
Manufacturer #:279640
The idler pulley with tri-ring and gasket, also known as a dryer belt tension pulley wheel, is used in dryers. This part maintains the right amount of tension for the belt to rotat...
$22.10
In Stock
(34)
PartSelect #:PS334278
Manufacturer #:279769
This kit includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse with a limit of 360 degrees Fahrenheit. The thermostat and fuse he...
$39.45
In Stock
(2)
PartSelect #:PS11740482
Manufacturer #:WP233520
This genuine OEM washer has a 3/4 inch outside diameter. This thrust washer can be used on most makes and models of dryers. A complete list of compatible dryers is available below....
$6.26
In Stock
(40)
PartSelect #:PS11722115
Manufacturer #:661570V
This drive belt is 93 1/2 inches long, and 1/4 of an inch wide, with 4 ribs and 3 grooves. To complete this repair, you will need a Phillips screw driver, a 1/4 inch nut driver, a ...
$23.76
In Stock
(32)
PartSelect #:PS11752609
Manufacturer #:WPW10314173
This is a drum support roller for a dryer. It is a genuine replacement part. The part includes the drum roller only and does not include the tri-rings. This part is sold separately...
$14.76
In Stock
(19)
PartSelect #:PS11746740
Manufacturer #:WP8577274
This internal bias thermostat is a replacement part for your dryer. To replace this part, you will need a putty knife, 5/16ths nut driver, a small flat blade screwdriver, and a 1/4...
$37.27
In Stock
(5)
PartSelect #:PS11755850
Manufacturer #:WPW10512946
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found b...
$8.26
In Stock
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Door Catch part had fallen out,/ was missing

Door Catch Kit – Part Number: 279570
  • Customer: Terri from Saint Augustine, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 645 of 684 people found this instruction helpful
Received your parts, Popped them both right into place, Even though only one side needed to be replaced, I wanted them to match up. It was amazing how easy this was. My husband was quite impressed I had ordered these rather then look for either a new or used dryer from some other source. read more

Burned out heater element

Dryer Heating Element – Part Number: WP3387747
  • Customer: Alan from Brooksville, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 438 of 490 people found this instruction helpful
Remove the kick plate from the bottom of the dryer by sliding a putty knife along the top edge to release the plastic clamps, one on each side about 4" in from the edges. The kick plate folds out and down. You will see the heat shield on the right, held in by one hex head screw. Remove screw and heat shield. The element is positioned in an open-front housing... read more

Dryer not heating

  • Customer: Wesley from Boyds, MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 276 of 311 people found this instruction helpful
Our dryer is 8 years old and had been slowly taking longer and longer to dry clothes, to the point that I was ready to purchase a new one. When the dryer stopped heating completely, I removed the bottom panel and found that the heating element was no longer working. I checked online and found this website. The top two recommended fixes for this issue was to... read more