10651159110 Kenmore Refrigerator - Instructions

1) Turn off the power to the refrigerator 2) Remove the top shelf and ice maker door 3)Remove three hex screws holding the ice maker in place, 4) Unplug the electrical cables and remove the ice maker 5) Remove the plastic cover to the motor module 6) Remove three screws from the motor module and seperate from the housing 7) Remove two mounting screws for the motor module 8) Seperate the motor module from the ice tray 9) Remove and replace the plastic ice stripper and rake10) Reassemble in reverse order. Note: Be patient after re-installing the ice maker. It might take an hour or two before its cold enough to kick back on and make ice.

Was very easy to take out the screw and put in the new coupler, then replace the screw. It is working great now.

Thought I was going to have to replace entire ice bin but went on this website and saw I only needed to replace a coupling. Even had video on how to do it. Easy greasy!!

Tough part was diagnosing the problem: bad water inlet solenoid, frozen inlet line, bad ice maker motor, or door opening sensor? Went to a parts shop & discussed the problem with the serviceman. He said you just need to sequentially replace each part. No way say I, that could cost $300 with a no-part return option.

I decided to replace the motor...Eureka!! It worked.
The underside of the ice maker cartridge has a plastic snap clip on either side of the cartridge. You need push each up, pull the left side of the cartridge out part way & disconnect the electrical connector on the right side(left..you facing the refrig.) With the cartridge out simply remove the 5 screws from the motor plate of the left side & replace with the new one.
Very simple. Slide the cartridge back in the frig. until the 2 snap clips click. Voila...you done! Cost $86..not $300. Apparently the motor is too weak to do the job & burns out quickly. Manufacturer should correct this defect.

i first removed the ice maker and took the motor assembley off. Right away i saw the problem. The wheel which drives the arm broke.
Once i get the new motor modl i just replaced it (it just pops into place with 1 or 2 screws).
put ice maker back in freezer and wola. Starting cranking out ice within 15 minutes.

I installed a Ice Door Kit. It works Great Now!

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

First I lifted the ice bucket out of the refrigerator, the broken coupling fell out in three pieces. I ordered a new coupling {$14 including shipping) It arrived 4 days later. I removed the phillips screw and installed the new coupling along with the flat washer that had fallen out. The repair took 5 minutes and saved a lot of money.

I unscrewed the screw holing the coupling in place.Made sure the washers whereput back in right and put the new coupling in and retightened the screw on the auger that holds the coupling in place and then put the ice bin back in place and away it went.

The ice dispenser stopped turning for crushed/cubed ice out the chute. Turned out it was this little $10 metal coupling part that broke apart. I'm guessing its not an unusual problem because the partSelect part was redesigned to be thicker than the original part to help prevent it from happening. I was very impressed with the superiour quality of the replacement part.

I removed the ice bin and on the bottom of it I removed 1 screw. I put the washer and drive lug on and reattached the screw. It was so simple I thought I surely left something off. It has worked fine since.

Used a screwdriver to pry loose the old switch, swapped wires to the new switch and pushed it into the opening. Took about 2 minutes.

Great service. Unpluged old switch and pluged in new one. Works great

A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.

The old coupling was no longer in the unit so I took out the set screw inserted the new coupling and reset the screw and now my ice maker works again like a champ. Less than 10 minute repair but took an extrea 5 as I had to mnake a new washer that goes under the coupling for wear resistance.