Models
>
KCMS135SWH0
KCMS135SWH0 KitchenAid Microwave - Overview
Sections of the KCMS135SWH0
[Viewing 6 of 6]Keep searches simple, eg. "belt" or "pump".
Screw
PartSelect #: PS11742721
Manufacturer #: WP488729
Metallic screw that is less than an inch long. Does not include the plastic washer.
$7.91
In Stock
Cooking Rack Support Clip
PartSelect #: PS11740786
Manufacturer #: WP3149478
Sold individually.
$8.83
In Stock
Stir Blade Drive Belt
PartSelect #: PS11740759
Manufacturer #: WP313646
This part connects the stir blade to the fan motor.
$49.90
In Stock
Screw
PartSelect #: PS11748102
Manufacturer #: WPW10068250
This screw is sold individually.
$6.08
In Stock
Fuse - 20Amp
PartSelect #: PS382366
Manufacturer #: 661172
This part helps protect your appliance from short circuits and power surges.
No Longer Available
Microwave Door Handle - White
PartSelect #: PS336949
Manufacturer #: 3149218
Does not include screws.
No Longer Available
Zip Tie
PartSelect #: PS11753208
Manufacturer #: WPW10339879
A zip tie, also known as a cable tie or a wire tie, is a fastening device that holds wires or tubing together. If a machine has wires or tubing that are easily shifted, you need to hold them tightly t...
$8.04
In Stock
Questions And Answers for KCMS135SWH0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Cooking rack support melted
Just pulled the old support out with pliers and installed the new one which snaps in. Not sure why the support melted as it has been the same one twice now. Keep extra support clips on hand, but no need as Parts Select had the new ones here next day.
Parts Used:
-
Ernie from Collinsville, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
6 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Belt on Wave Disperser
The microwave is the upper unit of combination microwave & conventional oven. Disconnect power to the unit. Slide unit out of built-in cabinet to expose the top shield of the microwave. Remove 5 screws holding top cover in place. Remove cover, which exposes the belt reel and drive motor. Install the new belt by threading it on the dr
... Read more
ive motor pulley, then walk the new belt on the stirrer pulley. Replace the top cover and reinstall the 5 screws. Reinstall the combination unit in the wall cabinet. Reconnect electrical power. Task Complete. The belt just seem to die of old age about every seven year. Without the wave disperser operating, the microwave oven does not give even heating.
Read less
Parts Used:
-
Harold from Foxfield, CO
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
6 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken belt on wave disperser
This microwave is the upper unit in combination with an oven. Microwave portion is Model RM288PXS. Cut power at breaker box. Remove metal frame around 2 sides and top, (5 screws). Remove 4 screws on bottom, whicn anchors the unit to the frame.Remove contol panel (2 screws at top) and swing down. Pull out female electrical socket at
... Read more
bottom right back in conrol unit space. Now pull out microwave from frame about 6-8 inches. This provides access to pulleys on the motor and wave disperser. Put on belt. Reverse the above procedure to finalize the repair. This is the 3rd time I have had to replace this belt. They last about 6-7 years. Without the wave disperser , the microwave does not provide even heat.
Read less
Parts Used:
-
Wendell from Hot Springs Village, AR
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
3 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!