Parts That Fix Hotpoint Refrigerator HSM25GFTASA Not dispensing water
Not dispensing water is a commonly reported symptom for the HSM25GFTASA Hotpoint Refrigerator, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your HSM25GFTASA Hotpoint Refrigerator that will fix Not dispensing water. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
This water inlet valve (Refrigerator Water Inlet Valve Assembly) supplies water to the ice maker and the water dispenser in your refrigerator. It is located at the back of the fridge, beneath the bottom panel. It is connected directly to 2 water supplies, a wiring harness, and your inlet water tube. This part is located at the back of the fridge, beneath the bottom panel. It is connected directly to 2 water supplies, a wiring harness, and your inlet water tube. Minerals and sediments can build up over time and cause a blockage in your inlet valve. They can also cause the valve to stick open, leading to an overflow of water. If this part is malfunctioning, water flow to your appliance could be compromised. Check for small ice cubes or a lack of ice cubes/water, as this is an obvious sign the part is damaged. The water inlet valve must be replaced if the solenoids no longer have continuity or the valve has internal blockage. Test your water inlet valve with a multimeter. You can test both the water dispenser side and the ice maker side. The part measures approximately 3 inches long and 2.75 inches wide and is constructed of plastic and metal. This replacement part features 1 dual inlet water valve with quick connections. It also has 1/4 and 5/16 John Guest fittings for the outlet lines and a 1/4 compression fitting for the inlet line.
Replacing your General Electric Refrigerator WATER VALVE WITH GUARD
Customer Repair Stories
Water dispenser not operating
-
michael from pennsburg, PA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Wrench set
Refrigertor water dispenser not working BUT ice machine is working
-
ralph from bristow, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers, Socket set
This OEM ice and water filter fits side-by-side and bottom-freezer GE models. The most common reason you would need to change this part is if you have never updated your model and it is no longer filtering your water. This also may lead to your refrigerator not dispensing water or ice properly. Manufacturers recommend you change your filter every six months to ensure it properly filters impurities. Depending on the model, a red light might also indicate that the filter is due for a replacement. Note: As per the manufacturer, this is an updated water filter. If you have never installed the updated part or your old model was made by Culligan, you may need the adapter to install the filter. See related parts. This filter is located inside the refrigerators upper right corner. It is common for water to drip from the dispenser when being changed so place a cloth underneath before you begin this repair. To remove the filter, turn it to the left until it releases without pulling down. Fill the new filter with tap water to prepare it. Position the new filter into the holder taking note of the arrows. The arrow on the front should be facing out. Gently push up on the filter and turn it to the right to secure it. Do not over-tighten. To release air in the system run 1-1/2 gallons of water through it. If your model has a reset button, press and hold this for a few seconds to reset it.
Replacing your General Electric Refrigerator Refrigerator Ice and Water Filter
Customer Repair Stories
water running slow
-
David from Tacoma, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Replace water filter
-
Alfred from Novato, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
This part is a possible option when ice door won't open or shut properly or when water is not dispensing.
Replacing your General Electric Refrigerator Dispenser Door Solenoid Assembly
Customer Repair Stories
Ice maker door not opening
-
scott from lake orion, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
Icemaker flap not closing, frosting up
-
Graeme from Sarasota, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Quick connector for plastic water line - 5/16" to 5/16"
Replacing your General Electric Refrigerator Union Connector - 5/16 Inch to 5/16 Inch
Customer Repair Stories
Moving the refrigerator into my new (very old) house we had to remove the doors which resulted in a crimped hose and union
-
Laura from Manchester, NH
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
My 13 yr grandson assisted me on this
-
Sherry from Auburn Hills, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
This is the replacement micro switch, or dispenser switch for your refrigerator. It is gray in color and measures approximately 1 inch by half an inch. The dispenser switch is what tells your refrigerator that it is ok to dispense ice or water. If your refrigerator is not dispensing ice or water, you may have a faulty or damaged switch. Be sure to disconnect the power to your refrigerator before you begin this repair. This switch is sold individually and is a genuine OEM replacement part sourced directly from the manufacturer.
Replacing your General Electric Refrigerator Micro Switch
Customer Repair Stories
Water dispenser won't always dispense water
My problem is the water dispenser does work intermittently. When we place the glass in position and hit the lever, the lights in the control panel go off and no water is dispensed. My next guess may be the water valve or the control panel. The icemaker makes ice but I have had problems with it dispensing for nearly a year now.
-
Curtis from Corona, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Water dispensor would not shut off
The difficult part was accessing the area to get to the micro switch.
The trim had to be removed, then the cover.
Then one unplug ... Read more s the board and removed the face plate which also contains the micro switch.
Once removed the two electrical terminals had to be disconnected, the micro switch installed and terminal reconnected.
Then reverse the removal procedure.
Then on to the double outlet replacement.
Suggest watching the installation video for the replacement although it was really a straight forward repair.
Two things to remember.
1. Unplug the fridge
2. Shut off the water to the dispenser
Overall it was not bad at all.
This was my first attempt at refrigerator repair and it went well.
Good luck on yours.
John
-
John from Mason, OH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
This electronic board (Main Control Board Assembly, Control Board, Motherboard) controls the temperature and defrost functions of the unit. This control board is located on the back of the refrigerator, and measures 8 inches by 5 inches. It’s constructed of metal and plastic, and comes in green. This kit includes one main control board with built in defrost controls. If broken due to electrical surges or normal use, your fridge may experience temperatures that are too warm or too cold, or inconsistent defrost cycles. If this happens, the part should be replaced.
Replacing your General Electric Main Control Board Assembly
The water filter head and tubing holds the water filter and comes with the water lines.
Customer Repair Stories
Water from door dispenser had slowed to a trickle
-
Richard from Mount Pleasant, SC
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Socket set, Wrench set
Will not dispense water
-
Thomas from Leland, NC
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Wrench set
This paddle, when your glass is pushed against it, activates the dispenser to release the ice through the funnel.
Customer Repair Stories
Ice funnel cracked
-
Jim from Glendale, AZ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Replace broken ice funnel dispenser cradle
-
David from Sparks, NV
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
This part helps to contain parts for the ice and water dispenser. The overlay and dispenser board is attached on the front of the housing shield.
This part is a replacement filter bypass cap for your refrigerator. If you intend to use an external water filtration system for your refrigerator, the bypass cap will allow you to do so. To use a filter bypass cap, simply screw it in where you would normally screw in the regular water filter. If you have a bypass system installed and your ice maker doesn’t make ice, your water dispenser doesn’t make water, or if there is water dripping inside your refrigerator, you may need to replace the bypass filter cap. This part is made of white plastic and is sold individually.
Customer Repair Stories
GE Profile Refrigerator Plug for Water Filter
-
Linda from Liberty, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Water if refigerator door is really slow. Ice making is really slow.
-
Fred from Edgartown, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
This “Dispenser Door Assembly” (Door Recess Assembly, Ice Door Assembly, Dispenser Door, Refrigerator Dispenser Ice Chute Door Kit, Dispenser Door Flap, Ice Chute Door, Flapper) keeps the room air from infiltrating the freezer. Once the lever is pressed, the door flap opens and allows the ice to dispense into your container. If your door flapper is broken, it could allow outside air to enter the freezer and alter the inside temperature. You may notice frost buildup surrounding the dispenser area. The door flap can disconnect from the dispenser lever, or the tabs that hold it in place may break. Frequent use may distort the sealing face and cause air leaks and frost buildup. This part mounts in the ice dispenser, and measures approximately 3.25 inches in diameter. It is constructed of plastic and rubber, and comes in white/black. This part is sold individually.
Replacing your General Electric Refrigerator Dispenser Door Assembly or Flapper
Customer Repair Stories
Flapper not sealing. Frost buildup on inside of freezer door
-
D from ZELLWOOD, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
This seems to be a design problem because I have to replace this part about every other year since we bought it. I tried to talk to GE but all they want to do is send a service man out to replace the part for about 100.00, But I do it for around 15.00. I just think they should find out why the rubbe
-
Jeff from Columbia City, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
This door recess spring or dispenser lever spring in your refrigerator is used to return the ice door to the closed position or the dispenser lever to the home position once released. You will find the spring in the water dispenser assembly, behind the main control panel. If the dispenser lever is malfunctioning or the dispenser ice door is not closing, you may need to replace this door recess spring.
Replacing your General Electric Refrigerator Recess Door Spring
Customer Repair Stories
The ice cube door located on the front of the freezer (side by side freezer/refridgerator) stopped closing.
-
Todd from Milton, WI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
frost build up
-
JOHNNY from FORT WORTH, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
The ice bucket auger is located within the ice bucket assembly in your freezer. It stirs and dispenses the ice in the bucket. You may need to replace the auger if your ice maker is noisy, or not dispensing ice. Disassembly of the ice bucket assembly is necessary to replace this part. Turn off power to the appliance before removing the ice bucket assembly to do this repair.
This part is the replacement torsion-fit spring for your refrigerator. It is made of metal and is sold individually. The torsion-fit spring provides tension to return the ice funnel back to its normal position after it dispenses ice. If your refrigerator is not dispensing ice or water properly, you may need to replace the torsion-fit spring. This is an OEM part sourced directly from the manufacturer.
The door recess crank for your refrigerator is located inside the water dispenser assembly. To access this part, you will need to take apart the dispenser assembly. To do this, you will need a putty knife and a Phillips screwdriver. If your dispenser door will not close properly, or ice is not dispensing properly, you may have a damaged door recess crank. This part is made of white plastic and is sold individually.
Replacing your General Electric Refrigerator Dispenser Door Recess Crank
This drawer slide rail is for the right side of your refrigerator. The drawer slide rail attaches horizontally to the refrigerator wall and supports the drawer so it can easily slide in and out. If the drawer slide track is broken, not sliding, or the fridge is not dispensing water, replacing this part could solve the issue. Make sure to unplug the refrigerator from the power source and wear gloves to protect your hands when installing this part. Refer to the diagram provided by the manufacturer for further guidance and instruction.
Replacing your General Electric Refrigerator Drawer Slide Rail - Right Side
Customer Repair Stories
Drawer slide rail for upper drawer had broken
Identifying the part on the website was a breeze t ... Read more oo, thanks to well-organized site, a picture of the part to match to my broken one, and even a video of a repairman making the repair. Couldn't have been easier, and probably saved me about $100.
-
Lanni from Irving, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Drawer slide broke due to overloading with beer.
-
Ashley from Brandon, MS
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
This defrost termination thermostat (Defrost Limiter Thermostat, High Limit Thermostat, Refrigerator Defrost Bi-Metal Thermostat) acts as a safety device to stop the evaporator coil from overheating, by turning off the defrost heater at the end of the defrost cycle. This part attaches to the tubing of the evaporator coil in the freezer. A faulty defrost termination thermostat may result in the defrost heater never heating and a solid frost buildup on the evaporator coil, which results in too warm temperatures. The thermostat contacts are normally closed and have continuity until it reaches 140 degrees. If this high limit thermostat is open at room temperature or colder, it is defective. This limit thermostat has an attached mounting clip and comes with pink and amber wire leads. The thermostat is 1 inch in diameter and 1/2 inch thick, the 2 wire leads are 10 inches long.
Replacing your General Electric Refrigerator Defrost Thermostat
Customer Repair Stories
freezer was freezing up.
-
doyle from kingston, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Socket set
Ice cubes froze in the tray and frost was all underneath
Note: If there is a large amount of ice build up on your coils a hair dryer works great. The drain is on the bottom anyway. Also , you may want to seal around the wire nuts to keep moisture out. I did
-
Michael from Sylva, NC
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
This part is a replacement recess trim for your refrigerator. It is the trim that runs around the perimeter of the ice/water dispenser. You will want to replace the recess trim if it is cracked or damaged. This part is black in color and is sold individually. It is approximately 16 inches long and 10 inches wide. It is a genuine OEM replacement part sourced directly from the manufacturer.
Customer Repair Stories
cracked trim
-
tom from santa monica, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
This is a manufacturer-approved drawer slide rail for your refrigerator. This slide rail is for the left side of the fridge. All you need to complete this repair is a Phillips screwdriver. Remove the shelves above and below the slide rail so you have room to access it. Unscrew the slide rail and replace it with the new one.
Replacing your General Electric Refrigerator Drawer Slide Rail - Left Side
Customer Repair Stories
slide rail broke causing shelf to fall
-
Mark from Albuquerque, NM
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
the left drawer slide rail was broken from years of use.
I then used a phillips head screwdriver to remove the 2 screws that held the slide in place.
After removing the broken slide rail, I installed the new rail, replaced the vegetable drawer and glass shelf. N ... Read more ew item worked like a charm.
The drawer slide arrived really quick after my order was placed. Approx. 2 days after ordering the part, it was on my front door step.
-
Carlton from Chino, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
This twelve volt dispenser light bulb is a little under two inches long.
Replacing your General Electric Refrigerator DISPENSER LIGHT
Customer Repair Stories
ice door light bulbs burned out
un screwed old bulb.
Screwed in new bulb.
Waa La,
There was light.
-
Austin from New Portland, ME
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
light burned out
-
Gerald from Lincoln, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins