Models
>
11GN-2W
11GN-2W Magic Chef Range - Overview
Sections of the 11GN-2W
[Viewing 4 of 4]Keep searches simple, eg. "belt" or "pump".
Light Bulb - 40W
PartSelect #: PS884734
Manufacturer #: 8009
This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are mos...
$11.73
In Stock
Door Handle Spacer Kit
PartSelect #: PS2003284
Manufacturer #: 12001735
This door handle spacer assembly contains two screws and two spacers.
No Longer Available
Light Bulb Socket
PartSelect #: PS11744030
Manufacturer #: WP74003387
This light bulb socket is located inside the oven cavity.
No Longer Available
GRATE BURNER
PartSelect #: PS12731250
Manufacturer #: W11400301
This square burner grate has sides measuring approximately nine inches. It is all black in color.
$106.04
In Stock
Door Side Seal
PartSelect #: PS11743946
Manufacturer #: WP7212P015-60
Sold individually. Order quantity required.
$62.20
In Stock
Oven Rack
PartSelect #: PS8769932
Manufacturer #: 7801P151-60
Sold individually.
No Longer Available
Oven Safety Valve
PartSelect #: PS2087949
Manufacturer #: 74010590
Once this valve senses the desired heat, this part will open up and allow the gas to travel to the oven burner.
No Longer Available
Capillary Clip
PartSelect #: PS2078936
Manufacturer #: 7112P053-60
This capillary tube clip is just under an inch long. It is made of metal.
No Longer Available
Questions And Answers for 11GN-2W
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
pilot lit but oven would light
replaced the oven safety valve. This device uses heat from the pilot to hold open a valve that allows gas from the thermostat control to feed the main burner. It works by boiling the liquid mercury in the sensor bulb, producing the pressure to hold open the valve. My sensor had failed from old age, leaking the mercury.
Spill ... Read more ed mercury needed to be collected and properly disposed, and the valve was a tough fit among the sheet metal parts that form the path for the gas to the burner slots. The valve is secured by flat head sheet metal screws and the gas plumbing is a tapered pipe fitting. The sensor bulb has a small steel spring to hold it in the proper spot to sense the pilot light.
I used gas-rated pipe dope on the gas fitting, probably unnecessarily. Valve faces only 1/2 psi pressure...
Spill ... Read more ed mercury needed to be collected and properly disposed, and the valve was a tough fit among the sheet metal parts that form the path for the gas to the burner slots. The valve is secured by flat head sheet metal screws and the gas plumbing is a tapered pipe fitting. The sensor bulb has a small steel spring to hold it in the proper spot to sense the pilot light.
I used gas-rated pipe dope on the gas fitting, probably unnecessarily. Valve faces only 1/2 psi pressure...
Read less
Parts Used:
-
Paul from Arlington, MA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Wrench set
19 of 26 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light bulb in water ice freezer door went bad
I didn't. Don't know how to get to light bulb to change it for this specific model
Parts Used:
-
Carl from RIVERSIDE, CA
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Screw drivers
7 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Parts Used:
-
Yafa (and David) from Bothell, WA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
5 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!